Woody’s® runners perfectly fit and guard the ski, while offering a cutting edge on hard-packed snow and ice. When tightened, Flat-Top® design offers increased surface area for less flexing and rocking with greater support and better steering than round top runners. All runners are made of durable steel with a combination of 60° carbide, hardweld and wear pads except Top-Stock® Hardweld Runners, which have no wear pad or carbide inserts.

Executive Series:

• 8 in. of 60 degree carbide with front and rear wear pads
• 1/2” round bar with Flat-Top® design
• Added balance for studded sleds

Trail Blazer IV Series:

• 6 in. of 60 degree carbide
• 1/2” round bar with Flat-Top® design
• Provides safety and control for both studded and un-studded sleds

Extender Trail III Series:

• 4 in. of 60 degree carbide
• 7/16” round bar with Flat-Top® design
• Entry-level carbide runner for lightly studded and un-studded sleds

Top Stock Hardweld Series:

• Steel round bar with Flat-Top® design
• Features strip of hardweld for added bar protection
• Not recommended for sleds with more than 48 studs

NOTE: Some models require drilling extra holes in skis to mount carbides. Dennis Kirk recommends removing any paint from the studs with a wire brush.

NOTE: These are short rods for models with E-Z Steer, for 27 in. 

Hard Surface type use part number 032050

Extender III type use part number 032051

Trail Blazer IV type use part number 032052

Executive Series type use part number 032053

NOTE: The models listed below have E-Z Steer as original equipment, which is retained w/the installation of this wear rod
Polaris Indy 340 Deluxe 1999-2002
Polaris Indy Sport Touring 2000-2003
Polaris Super Sport 1999-2001
Polaris Indy Trail/Trail Touring 1999-2003
Polaris Indy WideTrak LX 1999
Polaris Sport Touring 2004
Polaris Super Sport 2002-2005
Polaris Indy Trail 1995-1998/Trail Deluxe 1994-1995
Polaris Indy Trail Touring 1997-1998
Polaris Indy Ultra 1997-1998
Polaris Indy WideTrak 1995-1998 (all)
Polaris Indy XLT Limited 1997-1998
Polaris Indy XLT Special 1995-1997
Polaris Indy XLT Touring 1995-1997
Polaris Indy 440 1993-1997
Polaris Indy 500 Classic 1993-1998
Polaris Indy 500 Classic Touring 1993-1997
Polaris Indy 500 EFI 1996-1997
Polaris Indy 500 Classic/Classic Touring 1999-2000
Polaris Indy 500 XC SP 2000-2001
Polaris Indy 600 Touring 2000
Polaris Indy 700 SKS 1999-2000
Polaris Indy XLT Classic/Touring 1999
Polaris Indy 500 Classic Touring 1998
Polaris Indy Classic 1993-1998
Polaris Indy Classic Touring 1993-1997
Polaris Indy Lite Deluxe 1994-1998
Polaris Indy RXL 1994-1997 (all)
Polaris Indy Ultra Touring 1997

Dimensions:
Length: 13.75 in.
Stud Diameter/Length: 3/8 in./1-5/84 in.
Number of Studs: 2
Stud Center Mounting Distance From:
Front to 1st: 4.50 in.
1st to 2nd: 7.04 in.
2nd to End: 2.50 in.

(2) Wear rods

(4) Flange nylock nuts

Instructions