2003 Polaris RMK 700

What was your intended objective when you started the build?

To make a one of a kind sled that people would question what model it is.

What motivated you to start your project?

When I bought the sled I was wanting to fix the graphics. Then I realized, when I found a hood and seat from the 2004 Polaris Pro XR 800 that this was the direction I was going to go with the sleds colors and graphics. I have wanted the Pro XR 800 for a while so I built my RMK to look like one.

What was the most unique and creative thing you did to the sled?

When I installed the orange shorty seat, I designed and hand drilled custom RMK rails that fit on top of the tunnel between the seat and the back rack.

What are you most proud of?

The graphics that I designed and made and the custom RMK rails on the back of the tunnel. Also the slydog skis and bogie wheels really finish the sled. The front and rear suspension was stripped and re-powder coated with custom colors.

What do other people say about your snowmobile?

The neighbors thought it was an Arctic Cat, I laughed and said Polaris. My friends where amazed from what it looked like last winter. Other sled heads on facebook sayed holy fu**, that is sick.

13 Comments

Leave a Comment

Your email address will not be published. Required fields are marked *

Rate this build

- (0 ratings)
Submitted by: Jeff W

Submit your email to win fantastic prices. This is completely optional. Visit our email submission page to enter.

Specifics

Classification: Wild
Make, Model & Year: 2003 Polaris RMK 700
Time spent: 1200
Snowmobile cost: $1500
Money spent: $6000
Engine: Polaris 700 stock.
Intake: Mikuni TM 40 w/tps
Exhaust: stock exhaust with aftermarket can. Not sure what the can is, It came with sled
Drivetrain: New primary clutch and both clutches received the Epi TP-57 performance trail clutch kit. New challenger 144x15x2in track including a new drive shaft assembly.
Tunnel/Chassis Modifications: I installed a Polaris Pro XR 800 shorty seat on the tunnel. designed drilled and filed custom bag rails on top of the rear tunnel. wrapped the tunnel top in metallic orange, designed and made graphics for the sides of the tunnel. New Polaris snow flap and i trimmed some metallic orange vinyl for the molded Polaris on flap. made a bracket for the fuel shutoff I installed. Repaired a couple holes burned into the belly pan from the exhaust with resin and graphics cover it now.
Suspension: replaced all 4 front and rear shocks and coils with Fox Zero pro shocks. replaced the upper and lower front suspension rods plus new hardware and new rod ends. The lower front rods where bent. replaced both front steering rods also. front trailing arms where sand blasted and powdercoated silver. Rear suspension rails: needed straightened, one mount hole was oval, needed welded shut and re-drilled, top edges got smoothed and sanded, powder coated blue, the rear torque arms also got sand blasted. The front torque arm had one spot that got welded then they also got powder coated orange. bogie wheels got replaced with Slydog blue and orange custom wheels. The slides got replaced with dupont slides. pretty much all the long bolts and bushings where replaced also in the rear suspension. replaced coil spring guides, rear track tension bolts and all other bogie wheel bearings. New front limiter straps too.
Brakes: Installed new heavy duty brake pads.
Finish – Paint: Well, the sled used to be blue hood and seat with red trailing arms. I installed the Pro XR 800 Orange Hood and seat on the sled, Sanded and got hood support powder coated. wrapped the belt cover with metallic orange vinyl. replaced fuel lines with new orange lines, replaced wire wrap with blue wrap. I bought a belly panel from the 2004 Polaris Pro X2 just to copy the graphics on. Made new graphics for the belly panel, First layer of vinyl is low adhesion with the colored vinyl seams trimmed to match together and then a clear vinyl laminate on top. Then I measured the graphics for the hood and tunnel making them the same way I did for the belly panel. Installed orange vinyl on the windshield to match the Pro XR’s. I made a filler plate for the cutout in hood in front of the steering bar out of aluminum. I bent the sides to match the contour of the hood then applied orange metallic vinyl. Installed a new windshield.
Accessories: I replaced the pull rope with cobra cord and a new blue anodized aluminum handle. Replaced the oil reservoir and bought the toolbox cover. I also made a custom bracket for the inside of the cover so that the plastic wont cave in again. New Slydog skis, new blue front bumper.

Share