Dennis Kirk Inc.
Search Within
Ride Search
Top 3 Product Matches

Khrome Werks Chrome 1 in. Narrow +2 Sweeper 1 in. Handlebar - 300518

  • Part #:
    5900148
  • Manufacturer Part #:
    300518

MSRP Price: $109.95

Our Price: $98.96

You Save $10.99 (10%)
loading...
Overview of Khrome Werks Chrome 1 in. Narrow +2 Sweeper 1 in. Handlebar - 300518
  • Provide 2 7/16 in. additional pullback at the same height and width as factory
  • The throttle grip end is notched and the bar is milled for internal wiring to accommodate the electronic throttle control sensor unit (can also be used on pre-2008 models)
  • Cable changes may be required; wire extension for the ETC may or may not be needed
  • Dimpled, knurled and available in duplex nickel chrome plated finish
  • Made in the U.S.A.

    Included Items:
    (1) 1 in. chrome steel handlebar

    Width: 32 1/4 in
    Rise: 11 1/2 in.
    Center Width: 12 in.
    End Rise: 14 1/4 in.
    1 in. Diameter Clamping Width: 12 in.
    Inside Width of Knurling/Outside: 2 in./4 1/4 in.
    Drilled for Internal Wiring: Yes
    Dimpled to Prevent Pinching Control Wires: Yes
    Three Notches for 08-up H-D with Electronic Throttle: Yes

Specs for Khrome Werks Chrome 1 in. Narrow +2 Sweeper 1 in. Handlebar - 300518

Center Width 12 in.
Color Chrome
Description Dimpled
Diameter - Handlebar 1 in.
End Rise 12 3/4 in.
Finish Chrome
Overall Width 31 3/8 in.
Pullback/Sweep - Handlebars 7 5/8 in.
Rise 11 1/2 in.
Type Z & Custom
Units Each
Weight 3.85 lbs

Alternate/OEM Part Number(s):

06012857
Specs for Khrome Werks Chrome 1 in. Narrow +2 Sweeper 1 in. Handlebar - 300518
Center Width 12 in.
Color Chrome
Description Dimpled
Diameter - Handlebar 1 in.
End Rise 12 3/4 in.
Finish Chrome
Overall Width 31 3/8 in.
Pullback/Sweep - Handlebars 7 5/8 in.
Rise 11 1/2 in.
Type Z & Custom
Units Each
Weight 3.85 lbs
Fitment for Khrome Werks Chrome 1 in. Narrow +2 Sweeper 1 in. Handlebar - 300518

Part 5900148 fits the following machines

Make Sure This Fits Your Ride
5.0 / 5.0
10 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
10
0
0
0
0
Finish
5.0 / 5
Fit
4.9 / 5
Quality
5.0 / 5
Style
5.0 / 5
Value
5.0 / 5
Would you recommend this product?
Yes (8)
Finish
5 / 5
Fit
5 / 5
Quality
5 / 5
Value
5 / 5
Would you recommend this product?
Yes
Perfect!
Direct replacement of stock handlebars moving the controls 2 inches closer to the rider. The curved riser comes up over the tank facilitating a more natural location of the grips! None of the pieces H-D calls for in longer bars are required. H-D actually began leaving "slack" in the hydraulic clutch and brake lines as well as the wiring harnesses in 2014 I believe. I have heated grips and those were just long enough with some careful routing. This is one of the best videos on the install process: https://www.youtube.com/watch?v=sPvOmEvXQRs. Great solution to what seems to be an expensive upgrade to moving the control back toward the rider. Good Luck! 2017 FLHTK M8
May 4, 2017
Purchased
1 year ago
Finish
5 / 5
Fit
5 / 5
Quality
5 / 5
Value
5 / 5
Would you recommend this product?
Yes
Very good
October 12, 2017
Purchased
11 months ago
Fit
5 / 5
Quality
5 / 5
Style
5 / 5
Value
5 / 5
No Review Title Entered By User
No Review Text Entered By User
June 4, 2016
Fit
5 / 5
Quality
5 / 5
Style
5 / 5
Value
5 / 5
Nice Product
These bars seem to be well made. They were exactly what I needed. The 2" pullback also allowed me to put a ram mount for my GPS on my 2014 Street Glide. I have put on about 2,000 miles with them - and everything works well.
June 13, 2015
Finish
5 / 5
Fit
4 / 5
Quality
5 / 5
Value
5 / 5
Would you recommend this product?
Yes
Nice bars!
I installed these on my 2015 Harley ultra limited. They installed easily, although replacing bars is a time-consuming job.

I did need the switch wire extension kit that Harley sells make the wires from the switchgear on either grip long enough to plug into the bike. The bars are set up so you can run all the wires internally if you wish, although for maintenance purposes I left the switchgear wires external as they were from the factory.

Comfort wise these bars feel great. I no longer have to reach forward for the bars and then lift my chin to see, causing my shoulders and neck to cramp on longer rides.

The only minor issue I had, was the heated grip was on the throttle side, was dragging slightly on the end of the bar where it's cut to fit with the twist grip sensor. I ended up smoothing off the high point with a little sandpaper and it works just
fine now.

I recommend these handlebars!
January 23, 2017
Finish
5 / 5
Fit
5 / 5
Quality
5 / 5
Value
5 / 5
Would you recommend this product?
Yes
Pulled my hands back to a much more comfortable spot. No more leaning forward on my street glide
August 16, 2016
Purchased
over 2 years ago
Finish
5 / 5
Fit
5 / 5
Quality
5 / 5
Value
5 / 5
Would you recommend this product?
Yes
Good bars, Great value.
These bars put my 2017 Street Glide controls back just where they needed to be. I'm 5'8" and don't have a long reach. The stock bars are just a bit to short for me. The 2+ worked perfectly. I didn't have to extend the wires any, fits great. Instation wasn't hard, if you are mechanically inclined. Hardest part is running the throttle wire through the bars, but not too bad. Highly recommend.
June 25, 2018
Purchased
3 months ago
Finish
5 / 5
Fit
5 / 5
Quality
5 / 5
Value
5 / 5
Would you recommend this product?
Yes
Nice looking bars
Had these bars installed on my 2017 FLHXS and they look like they should be original equipment. Cables were run inside the bars without extending any wires or cables. I am no longer reaching for the bars like I was with the stock bars.and the stock mirrors are fine with narrow +2 sweepers. I just got the bike back from my HD shop and only have 50 miles with the new bars but I can tell these are going to be more comfortable on long hauls.
I will add that I am 5'2" and have a super reduced reach seat. I am glad that I did not get the 2+2 model.
September 20, 2017
Purchased
1 year ago
Finish
5 / 5
Fit
5 / 5
Quality
5 / 5
Value
5 / 5
Would you recommend this product?
Yes
Narrow sweeper bars
I originally wanted the 2+2 narrow sweeper bars for my 2014 HD Street Glide. I was told by 3 different sources that the 2+2s would not fit. So I went with the +2 narrow sweepers and they look and fit great. I'm 5'8 and to reach for the standard bars. These extended back enough to make for a very comfortable ride. Just a note on the 2+2 narrow sweeper bars, I did speak with a rep from Khrome Werks and he was absolute that the 2+2 bars would fit the 2014 St Glide. So if you need the extra height as well you may want to them. Very satisfied !!
April 5, 2018
Purchased
6 months ago
Finish
5 / 5
Fit
5 / 5
Quality
5 / 5
Value
5 / 5
Would you recommend this product?
Yes
Great bars
These worked great.. Good quality and speed of shipment.
August 24, 2016
Purchased
over 2 years ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 7 questions Browse 7 questions and 15 answers
Will this bar work on 2018 Road King? Will any cables need to be extended?
A shopper on May 12, 2018
BEST ANSWER: I had them installed on my 2017 Street glide special and the cables did not need to be extended. The tech just had to re route cables in my Fairing. I cannot say that they will fit the Road King as my cables might be a different length because of the fairing.
What will I need to do this replacement?
A shopper on Jan 2, 2018
BEST ANSWER: I had the HD shop install the bars, the tech did not have to extend any wires or cables. He ran the wires inside the bars and did not have to remove any wires from the plugs. My bike was a 2017 FLHXS and has the small connectors for the FBW throttle.
will these bars fit a 2016 flhxs?
gary w on Mar 22, 2017
BEST ANSWER: They fit perfect on my 2014 ultra classic
What is the difference between 2+ and 2+?2 khrome handlebars , I have 2014 hd trike .
A shopper on May 13, 2018
BEST ANSWER: Different pull back dimentions
will these fit a 2010 cvo street glide?
A shopper on May 6, 2017
BEST ANSWER: Universal, should fit
Will I need to extend the wiring on my 2016 FLHXS with these bars?
Dave T on Apr 30, 2017
BEST ANSWER: The clutch/brake lines will be long enough. You might be able to get by without the wire extensions for your switchgear, but it'd be pretty tight. I bought the extensions from Harley, they're only about $35, and it made installation pretty easy.
Looking for handlebars that fit 2003 yamaha v-star classic 1100 and cables . 10" to 12"?
Nick A on Apr 16, 2017
BEST ANSWER: these are for harley, N/A for yamaha
Instructions and Manuals for Khrome Werks Chrome 1 in. Narrow +2 Sweeper 1 in. Handlebar - 300518

You May Also Be Interested In