Dennis Kirk Inc.
Search Within
Ride Search
Top 3 Product Matches

Chrome 1 1/4 in. 2+2 Stretch Handlebar - 300302

  • Part #:
    599878
  • Mfg Part #:
    300302
  • OEM/Ref#:
1 / 1

Chrome 1 1/4 in. 2+2 Stretch Handlebar - 300302

  • Part #:
    599878
  • Mfg Part #:
    300302
  • OEM/Ref#:
Price: $230.95
Make sure this fits your ride
loading...
Ships Free
In Stock - 1 on Hand

Ships Today!
Order in the next
1 6
HR
3 9
MIN
5 0
SEC
Khrome Werks Chrome 1 1/4 in. 2+2 Stretch Handlebar - 300302
  • Diamond knurls for risers on 3.50 inch centers, elliptical center slot, slotted grips with the right side flattened for master cylinder clearance and notched for ETC
  • May be used on 1997-2007 models without ETC


Note: One piece upper riser clamp (H-D 55918-08) must be used when installing bars with center elliptical slot on pre-2008 baggers.

Note:For models listed with Bat Wing Fairings

Included Items:
(1) 1 1/4 in. chrome steel handlebar

Width: 35 1/2 in.
Rise: 13 1/2 in.
Pullback: 5 1/2 in.
Center Width: 11 1/2 in.
End Rise: 15 1/2 in.
1 in. Diameter Clamping Width: 9 1/2 in.
Inside Width of Knurling/Outside: 2 in./4 1/4 in.
Drilled for Internal Wiring: Yes
Dimpled to Prevent Pinching Control Wires: No
Three Notches for 08-Up H-D with Electronic Throttle: Yes
Specifications
Part #: 599878
Mfg #: 300302
Center Width 11 1/2 in.
Color Chrome
Description Knurled
Diameter - Handlebar 1 1/4 in.
End Rise 15 1/2 in.
Overall Width 35 1/2 in.
Pullback/Sweep - Handlebars 5 1/2 in.
Rise 13 1/2 in.
Type OEM Replacement Bend
Units Each
Weight 6.50 lbs
Alternate/OEM Part Number(s):
06012650
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Fitment for Khrome Werks Chrome 1 1/4 in. 2+2 Stretch Handlebar - 300302

Part 599878 fits the following machines

Harley-Davidson
  • Electra Glide - FLH 1984-1985
  • Electra Glide - FLHT 1984-1987
  • Electra Glide Classic - FLHTC 1984-2005, 2009-2013
  • Electra Glide Classic (EFI) - FLHTC 2007-2008
  • Electra Glide Classic Injected - FLHTC I 1995-2006
  • Electra Glide Injected CVO/SE - FLHTCSE 2004
  • Electra Glide Police - FLHTP 2007-2013
  • Electra Glide Special - FLHX 1984-1985
  • Electra Glide Standard - FLHT 1995-2006, 2009
  • Electra Glide Standard (EFI) - FLHT 2007-2008
  • Electra Glide Standard Injected - FLHT I 2003-2006
  • Electra Glide Ultra Classic - FLHTCU 1989-1999, 2009-2013
  • Electra Glide Ultra Classic (EFI) - FLHTCU 2007-2008
  • Electra Glide Ultra Classic Injected - FLHTCU I 1995-2006
  • Electra Glide Ultra Limited - FLHTK 2010-2013
  • Street Glide - FLHX 2006, 2009-2013
  • Street Glide (EFI) - FLHX 2007-2008
  • Street Glide Injected - FLHX I 2006
Reviews & Questions
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
Are these milled to accept the heated grips on the 2017 limited?
ALrider on Apr 29, 2017
BEST ANSWER: They won't fit that bike at all. There's no holes for the brake or clutch pins. I had to return them because I wasn't willing to drill and mill them to fit.
3.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
0
0
1
0
0
Finish
4.0 / 5
Fit
3.0 / 5
Quality
4.0 / 5
Value
5.0 / 5
Would you recommend this product?
Yes (1)
Finish
4 / 5
Fit
3 / 5
Quality
4 / 5
Value
5 / 5
Would you recommend this product?
Yes
Handle bars
I like the fit and angle that it rests my arms and wrists at. I like the ease of installation without having to extend the wires and brake lines. The reason for three stars is on my 2014 HD FLHXS is I found it necessary to grind notches on both sides control clamps to allow the wiring to pass through without pinching or cutting the harnesses. The notch in the handle bar was not long enough to allow the harnesses to pass through causing me to grind and reroute the harness. I also installed Kuryakyn ISO grips, the portion where the 1 inch tube was welded into the 1.25 inch portion was not set back far enough causing the controls to hold out on the grip. This caused quite a lot of end-play in the throttle grip. I don't know how far into the splines the grip was allowed to progress on the throttle by wire control so in time it might strip out the splines. It only needs about 1/8 inch to remove the end play and would require grinding the stepped area where the tubes meet back to allow the control clamps to be secured a bit deeper and the grip to fully engage the throttle control splines. I worry stripped splines will be a future issue without doing so.
September 12, 2018
Purchased
1 year ago