Overview of J&M Corporation Rokker XXRP 630W 4-CH DSP Programmable Amplifier Kit - JAMP-630HR15RCP
This new J&M ROKKER XXRP DSP controlled 4-channel 630 watt RMS fairing/rear speaker amplifier kit has been designed specifically for use on the 2015-2016 Harley® RoadGlide (NOT for CVO) with the stock Harley radio (either version NO radio FLASH required) with rear-lid or lower-fairing speakers added.
The specific green-band plug-n-play RCA input harnesses included with this amplifier kit, take the 2-channels of audio signal available from the RoadGlide version of the Harley Infotainment radio and provides 4 separate channels of amplification at 157.5 watts RMS continuous power per-channel into a 2 or 4-ohm speaker load. (Manually selectable on the amplifier itself for a 2-ohm or 4-ohm speaker load)
This is a full range class D digital amplifier properly shielded against RF interference into the AM or FM stereo radio bands. The ROKKER XXRP amplifier uses advanced digital switching power supply technology to dramatically reduce the 12v current demands on the motorcycle electrical system, compared to other brand amplifiers in this power range. Amplifier mounts to the custom made stainless steel 2-piece bracket system, to provide solid and secure mounting inside the RoadGlide fairing, in addition to blocking amplifier heat from being transferred to the radio.
These new ROKKER XXRP series amplifiers are fully programmable thru the internal digital signal processor (DSP) and come out of the box already dialed in for this specific RoadGlide custom speaker configuration, to provide maximum highway performance from your Harley Davidson audio system.
Should you wish to alter these DSP settings using the internal programming dongle already built into this new amplifier, (USB computer connection cable also included with this amplifier kit) all of our specific custom amplifier programs are now available as a consumer download from the J&M website @ www.jmcorp.com.
Also included are our custom made heavy-gauge power and ground wires used for the fused battery & frame connections, along with all necessary mounting hardware & complete installation/operation instructions.
Amplifier itself measures 8 1/4” Long X 5 1/8” Wide X 1 5/8” Tall.
(1) 8-1/4" long x 5-1/8" wide x 1-5/8" tall AMP W/(4) female audio connectors, (1) 2 pin male connector & (1) 10 pin female connector
(1) 65" Wire harness W/(1) 30 amp in-line fuse, (2) ring terminals and (1) 2 pin female connector
(1) 31-1/2" wire harness W/(4) male audio connectors & (2) 2 pin male connectors
(1) 17-1/2" red and black wires W/(1) tiny light & (1) 2 pin female connector
(1) 20-1/2" USB cable
(1) Wiring harness W/(1) 9 pin female connector, (3) 2 pin female connectors, (1) 4 pin male connector & (1) 2 pin male connecor
(12) 8" Black cable ties
Cross reference number(s):44050438
Specs for J&M Corporation Rokker XXRP 630W 4-CH DSP Programmable Amplifier Kit - JAMP-630HR15RCP
|Ohm Rating||2 ohm|
|Ohm Rating||4 ohm|
|Total Watt Output||157.5w|
Fitment for J&M Corporation Rokker XXRP 630W 4-CH DSP Programmable Amplifier Kit - JAMP-630HR15RCPSee if this part fits your ride
Part 4000884 fits the following machines
- 2016 Harley-Davidson Road Glide - FLTRX
- 2015 Harley-Davidson Road Glide - FLTRX
- 2016 Harley-Davidson Road Glide Special - FLTRXS
- 2015 Harley-Davidson Road Glide Special - FLTRXS
- 2016 Harley-Davidson Road Glide Ultra - FLTRU