Track Tool

$68.99 Woodys Steel Stud Sharpening Tool for 30 degree angle TOOL-SHARP-3
Manufacturer: Woodys
Dennis Kirk Part #: 080392
Woodys Steel Stud Sharpening Tool for 30 degree angle: Manufacturer part # TOOL-SHARP-3 - If your studs are sharp, your studs are safe. Fits into a 3/8 in. or larger drill chuck. Sharpens studs easily -even when they're still on your sled. Available for studs with 30º angles.. TOOL-SHARP-3
8 on hand

More Info/Options for Woodys Steel Stud Sharpening Tool for 30 degree angle TOOL-SHARP-3

Track Tool

$18.99 Woodys 5/16 Indexing Tool for Square Support Plates SPI-TOOL-5
Manufacturer: Woodys
Dennis Kirk Part #: 280001
Woodys 5/16 Indexing Tool for Square Support Plates: Manufacturer part # SPI-TOOL-5 - Fits on standard 3/8 in. drive ratchet handle and holds square support plate when nut is tightened to secure stud.. SPI-TOOL-5
7 on hand

More Info/Options for Woodys 5/16 Indexing Tool for Square Support Plates SPI-TOOL-5

Track Tool

$68.99 Woodys Steel Stud Sharpening Tool for 60 degree angle TOOL-SHARP-6
Manufacturer: Woodys
Dennis Kirk Part #: 080394
Woodys Steel Stud Sharpening Tool for 60 degree angle: Manufacturer part # TOOL-SHARP-6 - If your studs are sharp, your studs are safe. Fits into a 3/8 in. or larger drill chuck. Available for studs with 30°, 45° or 60° angles.. TOOL-SHARP-6
1 on hand

More Info/Options for Woodys Steel Stud Sharpening Tool for 60 degree angle TOOL-SHARP-6

Track Tool

$24.99 Woodys Indexing Tool for Triangle Support Plates SPI-TOOL-T
Manufacturer: Woodys
Dennis Kirk Part #: 282675
Woodys Indexing Tool for Triangle Support Plates: Manufacturer part # SPI-TOOL-T - Save time and knuckles. Stud size, 5/16in. and 7mm. Fit on standard 3/8 in. drive ratchet handle and index support plates.. SPI-TOOL-T
2 on hand

More Info/Options for Woodys Indexing Tool for Triangle Support Plates SPI-TOOL-T

Track Tool

$68.99 Woodys Steel Stud Sharpening Tool for 45 degree angle TOOL-SHARP-4
Manufacturer: Woodys
Dennis Kirk Part #: 080393
Woodys Steel Stud Sharpening Tool for 45 degree angle : Manufacturer part # TOOL-SHARP-4 - If your studs are sharp, your studs are safe. Fits into a 3/8 in. or larger drill chuck. Sharpens studs easily - even when they're still on your sled. Available for studs 45° angles.. TOOL-SHARP-4
2 on hand

More Info/Options for Woodys Steel Stud Sharpening Tool for 45 degree angle TOOL-SHARP-4

Track Tool

$13.99 Sno-Stuff Track Cutter Tool 725-016
Manufacturer: Sno-Stuff
Dennis Kirk Part #: 28495
Sno-Stuff Track Cutter Tool: Manufacturer part # 725-016 - Allows you to make a clean cut hole through rubber tracks for installing studs. Available for 5/16 in. stud thread size. Can be used either by hand or with an electric drill. Resharpenable.. 725-016
More than 10 on hand

More Info/Options for Sno-Stuff Track Cutter Tool 725-016

Track Tool

$68.95 Parts Unlimited Track Clip Tool 16040001
Manufacturer: Parts Unlimited
Dennis Kirk Part #: 282087
Parts Unlimited Track Clip Tool: Manufacturer part # 16040001 - Perfect for installing many types of track clips. Kit comes complete with one 5/16 in.-11 x 6 in. screw, one pressure plate, two washers, two 1/2 in.-20 x 6 in. hexagonal screws and one #1 bending block for large clips. Also includes on #2 bending block for narrow clips, one male block and two hexagonal screws. Works on Camoplast and many other track clips except full-block style tracks (those with rubber accross the top of the clips). Will not work on all Camoplast tracks or the following Kimpex tracks:, X-Force, X-Trail 00-004 Series, Ultimat Traxtion, Tomahawk, Xcavator.. 16040001
More than 10 on hand

More Info/Options for Parts Unlimited Track Clip Tool 16040001

Track Tool

$79.95 Fast-Trac Track Clip Tool Y01
Manufacturer: Fast-Trac
Dennis Kirk Part #: 2805
Fast-Trac Track Clip Tool: Manufacturer part # Y01 - Replace track clips and clip-on slider guides the easy way with our track clip tool. Hardened steel for extended service life. Replaces clips on Yokohama involute drive and most other rubber tracks that use clips (minimum drive hole width of 1 1/2"). Threads of bolt must be lubricated prior to use. These bolts have a tendancy to be tight and hard to turn when new. , Not for use with Camoplast Tracks.. Y01
More than 10 on hand

More Info/Options for Fast-Trac Track Clip Tool Y01

Track Tool

$94.99 Motion Pro Snowmobile Track Cutting Tool p282925
Manufacturer: Motion Pro
Dennis Kirk Part #: 282925
Motion Pro Snowmobile Track Cutting Tool: Manufacturer part # p282925 - Cuts stud installation time in half when used with Stud Installation Tool PART NO. 28-2926 (sold separately). Reduces stud pullout by cutting a consistent, precise, straight non-tapered hole in the track without ragged edge, which produces a consistent and proper interference fit between studs and track. Will not inadvertently plunge through the track and damage the undercarriage or bogie wheels. Can be used anywhere - no power tools needed; long-wearing Acme thread only requires a couple turns of the handle to cut a hole in the track. Convenient handle tube stores up to 150 track plugs for easy disposal; a small hole in the handle tube allows an air nozzle to be used to remove stubborn track plugs. Replaceable heat-treated 3/8 in. (9.5 mm) diameter steel cutter; cutter stop can be turned over and replaced when worn out. Body features a cutaway section surrounding the Acme thread for an unobstructed view of stud locating marks or dimples placed on the track. Ergonomically designed T-handle; sturdy zinc-plated steel construction. Joe Bolger Designs.. p282925
Expected Soon

More Info/Options for Motion Pro Snowmobile Track Cutting Tool p282925

Track Tool

$10.99 Woodys Track Cutter 1/4 in. DRIL-1/4
Manufacturer: Woodys
Dennis Kirk Part #: 28491
Woodys Track Cutter 1/4 in.: Manufacturer part # DRIL-1/4 - Stud pattern drilling made quick and easy. Use for all types of studs; cuts a fabulous clean hole.. DRIL-1/4
More than 10 on hand

More Info/Options for Woodys Track Cutter 1/4 in. DRIL-1/4

Track Tool

$37.99 Woodys Track Tension Tool TRAK-TOOL
Manufacturer: Woodys
Dennis Kirk Part #: 282676
Woodys Track Tension Tool: Manufacturer part # TRAK-TOOL - Use to adjust the tracks tension according to the manufacturers guidelines.. TRAK-TOOL
More than 10 on hand

More Info/Options for Woodys Track Tension Tool TRAK-TOOL

Track Tool

$10.99 Woodys Track Cutter 7 mm DRIL-7MM
Manufacturer: Woodys
Dennis Kirk Part #: 28492
Woodys Track Cutter 7 mm: Manufacturer part # DRIL-7MM - Stud pattern drilling made quick and easy. Use for all types of studs; cuts a fabulous clean hole.. DRIL-7MM
More than 10 on hand

More Info/Options for Woodys Track Cutter 7 mm DRIL-7MM

Track Tool

Track Tool