$422.99V-Factor Stretched Chopper Gas Tank -Flush Mount Cap 81073
Manufacturer: V-Factor
Dennis Kirk Part #: H18776
V-Factor Stretched Chopper Gas Tank -Flush Mount Cap: Manufacturer part # 81073 - 4.5 in. stretched chopper gas tank. 4.7 Gallon capacity. Mounting brackets are rubber isolated to prevent vibration cracks. "Weld to frame" brackets recess in the bottom of the tank for a hidden look. Include chrome plated pop-up gas cap. Tapped 1/8" 27 NPT at rear of tank for gas crossover line (not included). Use with 3/16" (22mm) fuel valve. Raw steel finish. Frame requirements: 4" stretch in the front down tubes 3" minimum stretch in the backbone Backbone o.d. cannot exceed 1 3/4", , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. 81073 2 on hand
$413.99V-Factor Stretched Chopper Gas Tank -Flush Mount Cap 81075
Manufacturer: V-Factor
Dennis Kirk Part #: H18778
V-Factor Stretched Chopper Gas Tank -Flush Mount Cap: Manufacturer part # 81075 - 4 in. Stretch/4.1 Gallon Capacity. Mounting brackets are rubber isolated to prevent vibration cracks. "Weld to frame" brackets recess in the bottom of the tank for a hidden look. Include chrome plated pop-up gas cap. Tapped 1/8 27 NPT at rear of tank for gas crossover line (not included). Use with 13/16 in. (22mm) fuel valve. Raw steel finish. Frame requirements: 4 in. stretch in the front down tubes; 3 in. minimum stretch in the backbone; backbone o.d. cannot exceed 1 3/4 in., , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. 81075 2 on hand
$1115.99Russ Wernimont Designs Fuel-Injected Gas Tank - 20 1/2 in. wide 07010189
Manufacturer: Russ Wernimont Designs
Dennis Kirk Part #: 183331
Russ Wernimont Designs Fuel-Injected Gas Tank - 20 1/2 in. wide: Manufacturer part # 07010189 - 6-gallon one-piece tanks are 1 1/2 in. wider than stock tanks. Feature a 3 in. stretch and curved bottom for a custom look. Replace the existing dash with the included raw dash panel. Includes a factory sealed powder-coated primer finish. Stock OEM fuel-pump assemblies work with the fuel-injected tanks and use a L96-06 vented gas cap. Carb tanks include a filler plate and neck assembly that uses a L96-06 vented gas cap. Tanks fit with RWD ProTour (454539) and Profile (454538) Seats, sold separately - Danny Grey seats also available: 455060, 455061, 455062, 455063, 455064, 455065, 455066, 455067. Made in the U.S.A.. , NOTE: Filler plate on carb tanks may require modifications to reinstall early-style sending units, , NOTE: This item ships 3 or 4 days after the order is placed, , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. 07010189 1 on hand
$889.99Russ Wernimont Designs Smooth-Top Gas Tank 1914-0010
Manufacturer: Russ Wernimont Designs
Dennis Kirk Part #: H18709
Russ Wernimont Designs Smooth-Top Gas Tank: Manufacturer part # 1914-0010 - The master fender builder finally turns his attention to gas tanks. Beautiful, one-piece, single-cap designs handcrafted from 14- and 16-gauge steel. Universal 5 in. stretch tank fits most custom frames. Measures 25 in. L x 13 1/2 in. W. Tanks is designed to use vented gas cap for L96-03 models and 22mm petcock (sold separately), , NOTE: Not for use on fuel-injected models, , NOTE: FXSTD models require the use of a custom seat, , NOTE: Tank is pictured on the left DK Part no. H18708 is pictured on the right, , NOTE: This item ships 3-4 days after order is placed, , WARNING: , All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems. 1914-0010 1 on hand
$1115.99Russ Wernimont Designs Carb Gas Tank - 17 1/2 in. wide p183703
Manufacturer: Russ Wernimont Designs
Dennis Kirk Part #: 183704
Russ Wernimont Designs Carb Gas Tank - 17 1/2 in. wide: Manufacturer part # p183703 - 17 1/2" and 20 1/2 in. widths are now available. A 3 in. stretch is featured on one-piece tanks. Curved bottom provides a custom look. Raw dash panel replaces the existing dash. Inside of tanks have a factory sealed powder coat primer. OEM fuel-pump assemblies are accepted on 03-07 style fuel-injected tanks and 96-06 style carb tanks include a filler plate/neck assembly; both use L96-08 non-vented gas caps. Approximate 6-gallon capacity. Tanks fit with RWD Profile (454538) and ProTour (454539) Seats, sold separately - Danny Grey seats also available: 455060, 455061, 455062, 455063, 455064, 455065, 455066, 455067. Made in the U.S.A.. , Dimensions , Length: 22 1/2 in., Width: 18 in., Tunnel Length: 18 1/2 in., , Tunnel Width , Front: 3 1/2 in., Rear: 5 in., , Tunnel Depth: , Front: 4 1/2 in., Rear: 4 1/4 in., , Tank Height: 9 in., Fuel Petcock: Left Rear, Petcock Thread Size: 22mm, Gas Cap Type: Threaded, Fuel Pump Tabs: No, , NOTE: Filler plate on carb tanks may require modifications to reinstall early-style sending unit., , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. p183703 1 on hand
$1115.99Russ Wernimont Designs Carb Gas Tank - 20 1/2 in. wide RWD-800C
Manufacturer: Russ Wernimont Designs
Dennis Kirk Part #: 183040
Russ Wernimont Designs Carb Gas Tank - 20 1/2 in. wide: Manufacturer part # RWD-800C - 6-gallon one-piece tanks are 1 1/2 in. wider than stock tanks. Feature a 3 in. stretch and curved bottom for a custom look. Replace the existing dash with the included raw dash panel. Includes a factory sealed powder-coated primer finish. Carb tanks include a filler plate and neck assembly that uses a L96-06 vented gas cap. Tanks fit with RWD ProTour (454539) and Profile (454538) Seats, sold separately - Danny Grey seats also available: 455060, 455061, 455062, 455063, 455064, 455065, 455066, 455067. Made in the U.S.A.. , NOTE: Filler plate on carb tanks may require modifications to reinstall early-style sending units, , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. RWD-800C 1 on hand
$876.99Russ Wernimont Designs Smooth-Top Gas Tank 1914-0009
Manufacturer: Russ Wernimont Designs
Dennis Kirk Part #: H18708
Russ Wernimont Designs Smooth-Top Gas Tank: Manufacturer part # 1914-0009 - The master fender builder finally turns his attention to gas tanks. Beautiful, one-piece, single-cap designs handcrafted from 14- and 16-gauge steel. For Softail Frame the gauges, indicator lights and ignition switch must be relocated. Measures 21 1/4 in. L x 15 1/2 in. W. Tank is designed to use vented gas cap for L96-03 models and 22mm petcock (sold separately), , NOTE: Not for use on fuel-injected models, , NOTE: FXSTD models require the use of a custom seat, , NOTE: This item ships 3-4 days after the order is placed, , WARNING: , All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems. 1914-0009 1 on hand
$649.99Eddie Trottas Thunder Design Thunder D-Seat Oil Tank TC-283
Manufacturer: Eddie Trottas Thunder Design
Dennis Kirk Part #: 493925
Eddie Trottas Thunder Design Thunder D-Seat Oil Tank: Manufacturer part # TC-283 - Oil tank for Softail-style batteries. Includes threaded cap, , NOTE: Fits Thunder Cycle ST300 frames only.. TC-283 1 on hand
$11.99Pingel Threaded Tank Bung 22A
Manufacturer: Pingel
Dennis Kirk Part #: 182928
Pingel Threaded Tank Bung: Manufacturer part # 22A - For use when installing a custom gas tank or need to repair your stock tank. Male tank bung with 22mm threads (same as OEM). Designed to be welded directly to the tank. Made in the U.S.A... 22A 2 on hand
$39.99Pingel Tank Fitting Kit for Fuel-Injection to Carburetor Conversion 62052
Manufacturer: Pingel
Dennis Kirk Part #: 182923
Pingel Tank Fitting Kit for Fuel-Injection to Carburetor Conversion: Manufacturer part # 62052 - For the models listed with Magnetti Marelli EFI. Fuel-injection can't keep up with the demands of your high-powered engine? Use these tank fittings when converting to a carburetor. Kits include the stainless steel tank fittings you need to install a high-quality, high-flow Pingel fuel valve. Made in the U.S.A.. , , NOTE: Due to tight tolerances in the tank fittings, a Pingel fuel valve is the only one that will fit... 62052 Expected Soon
$137.99Paughco Custom 1-Piece Fatbob Style Gas Tank 820
Manufacturer: Paughco
Dennis Kirk Part #: 183278
Paughco Custom 1-Piece Fatbob Style Gas Tank: Manufacturer part # 820 - . A single cap, two petcock outlets. A high tunnel for the Fatbob look, one left side petcock outlet and a hole-to-hole center line on mounting brackets of 17 11/16 in. are featured on the Extra Wide Mustang. A left side external petcock outlet, indent on tank bottom for rocker box clearance and a hole-to-hole center line on mounting brackets of 19 3/4 in. are featured on the 1-piece Fatbob (19 1/2 in. L x 13 in. W x 8 in. D; Tunnel measures 2 3/16 in. W x 4 1/4 in. D). , DIMENSIONS: , Length: 20-1/2 in., Width: 13 in., Tunnel Length: 19 in., , TUNNEL WIDTH: , Front: 2-1/4 in., Rear: 2-1/4 in., , TUNNEL DEPTH: , Front: 4 in., Rear: 2 in., , Tank Height: 9-1/2 in., Fuel Petcock: Left center, Petcock Thread Size: 22mm, Gas Cap Thread: Cam style , NOTE: Paughco recommends all tanks be mounted on leather spacers or bushings. , , NOTE: Will not work on any stock FXR or FLT, , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. 820 1 on hand
$280.99Paughco Center Fill Round Oil Tank p493718
Manufacturer: Paughco
Dennis Kirk Part #: 493718
Paughco Center Fill Round Oil Tank: Manufacturer part # p493718 - Chrome-finished 3.5 quart oil tank. 1/4" pipe feed and return and 1/8" pipe vent are featured. Measures 6" in dia. and 11 1/2" W.. p493718 Expected Soon
Moose Extended Lift Push Tube
Vance & Hines Dresser Dual Header Pipes 16729
Motion Pro SyncPro Carburetor Tuner
Kuryakyn Wheel Chock 922
Vance & Hines Big Radius Exhaust 26029
Caliber Poly-Shield III Salt Shield 13401
Parts Unlimited Large Universal Cover CS-1002
Kuryakyn Condor Pit-Stop/Trailer Stop Wheel Chock 920
Parts Unlimited Total Cover TC-1005
Vance & Hines Straight Shot HS Slip-Ons 16819
Vance & Hines Big Shot Duals 17925
Caliber LowPro Low Profile Wide 8 in. Trailer Guide and Protection System 13322
HJC Electric Shield
Battery Tender Battery Tender Jr. 12-Volt Model
BUB Rinehart 3 1/2 in. Slip-On Mufflers
Kuryakyn GranTour Bag 4141
Vance & Hines Big Radius Exhaust 26003
NGK Resistor Spark Plug BR9ES
JPS Blue Polyurethane Fuel Line
HJC Universal Quick Release Buckle
RBI Inc Bearing OEM Standard No 62052RS
