$270.99Dynojet Quick Shifter Pull Type Tension Sensor 4101
Manufacturer: Dynojet
Dennis Kirk Part #: 270914
Dynojet Quick Shifter Pull Type Tension Sensor: Manufacturer part # 4101 - The Dynojet Quick Shifter (DQS) kit allows full-throttle, clutchless upshifts. Shift rod pressure/tension sensor kit is a universal sensor that mounts to the shift rod in either a push or pull configuration. Requires modification of gear-linkage tie-rod. Linear travel sensor kit works with bikes that have no shift rod, or on which the shift rod pressure/tension sensor will not fit. Mounts to the shift lever on one end and to a fixed point on the chassis on the other. Universal mounting kit included. DQS is compatible with all PCIIIUSB Power Commanders and plugs into the expansion port with no splicing or re-wiring required. Power Commander Control Center software allows the rider to adjust engine kill time during upshifts, and makes it possible to set minimum rpm engine speeds for system operation. NOTE: Shift rod sold separately; order by make/model/year NOTE: To order either of the above sensors, the user must determine the correct direction of movement during the upshift (push or pull). If using the shift rod/pressure/tension sensor, press on the shift lever in the direction of an upshift and see if the rod is pushing or pulling on the clevis on the shift shaft. For the linear travel sensor, the shifter is also moved in the direction of an upshift. If the movement is down then a pull sensor is needed. If the movement is up a push sensor is required. Power Commander PCII, PCIII and PCIIIr are not compatible with the DSQ. 4101 3 on hand
CLEARANCE!
Was: $218.99
Now: $164.24
Dynojet Universal Ignition Quick Shifter Module 4111
Manufacturer: Dynojet
Dennis Kirk Part #: 271188
Dynojet Universal Ignition Quick Shifter Module: Manufacturer part # 4111 - Created to work on up to four cylinders for all carbureted and fuel-injected motorcycles. Allows full throttle, clutchless upshifts. Depending on the usage, you can switch from road to race settings. Universal and universal stick coil harnesses sold separately. Does not require a power commander. To get a complete system you must order a Universal Quick Shifter Module, a universal harness or universal stick coil harness, a Quick Shifter Sensor and rod.. 4111 3 on hand
CLEARANCE!
Was: $80.99
Now: $60.74
Dynojet Universal Quick Shift Stick Coil Harness 76911002
Manufacturer: Dynojet
Dennis Kirk Part #: 211841
Dynojet Universal Quick Shift Stick Coil Harness: Manufacturer part # 76911002 - Created to work on up to four cylinders for all carbureted and fuel-injected motorcycles. Allows full throttle, clutchless upshifts. Depending on the usage, you can switch from ?road? to ?race? settings. Universal and universal stick coil harnesses sold separately. Does not require a power commander. To get a complete system you must order a Universal Quick Shifter Module, a universal harness or universal stick coil harness, a Quick Shifter Sensor and rod. , NOTE: Denso coils on each spark plug. 76911002 1 on hand
CLEARANCE!
Was: $37.99
Now: $28.49
Dynojet Universal Quick Shift Wire Harness 76911001
Manufacturer: Dynojet
Dennis Kirk Part #: 211840
Dynojet Universal Quick Shift Wire Harness: Manufacturer part # 76911001 - Used with the Universal Quick Shift Module part number 271188.. 76911001 1 on hand
$299.99Dynojet Universal Ignition Quick Shifter Module p271926
Manufacturer: Dynojet
Dennis Kirk Part #: 271926
Dynojet Universal Ignition Quick Shifter Module: Manufacturer part # p271926 - Created to work on up to four cylinders for all carbureted and fuel-injected motorcycles. Allows full throttle, clutchless upshifts. Depending on the usage, you can switch from "road" to "race" settings. Does not require a power commander. All necessary wires and connectors are included. To get a complete system you must order a Universal Quick Shifter Module, a universal harness, a Quick Shifter Sensor and rod.. p271926 1 on hand
$270.99Dynojet Quick Shifter Push Type Tension Sensor 4102
Manufacturer: Dynojet
Dennis Kirk Part #: 270915
Dynojet Quick Shifter Push Type Tension Sensor: Manufacturer part # 4102 - The Dynojet Quick Shifter (DQS) kit allows full-throttle, clutchless upshifts. Shift rod pressure/tension sensor kit is a universal sensor that mounts to the shift rod in either a push or pull configuration. Requires modification of gear-linkage tie-rod. Linear travel sensor kit works with bikes that have no shift rod, or on which the shift rod pressure/tension sensor will not fit. Mounts to the shift lever on one end and to a fixed point on the chassis on the other. Universal mounting kit included. DQS is compatible with all PCIIIUSB Power Commanders and plugs into the expansion port with no splicing or re-wiring required. Power Commander Control Center software allows the rider to adjust engine kill time during upshifts, and makes it possible to set minimum rpm engine speeds for system operation. NOTE: Shift rod sold separately; order by make/model/year NOTE: To order either of the above sensors, the user must determine the correct direction of movement during the upshift (push or pull). If using the shift rod/pressure/tension sensor, press on the shift lever in the direction of an upshift and see if the rod is pushing or pulling on the clevis on the shift shaft. For the linear travel sensor, the shifter is also moved in the direction of an upshift. If the movement is down then a pull sensor is needed. If the movement is up a push sensor is required. Power Commander PCII, PCIII and PCIIIr are not compatible with the DSQ. 4102 3 on hand
$270.99Dynojet Quick Shifter Pull Type Linear Sensor 4103
Manufacturer: Dynojet
Dennis Kirk Part #: 270916
Dynojet Quick Shifter Pull Type Linear Sensor: Manufacturer part # 4103 - The Dynojet Quick Shifter (DQS) kit allows full-throttle, clutchless upshifts. Shift rod pressure/tension sensor kit is a universal sensor that mounts to the shift rod in either a push or pull configuration. Requires modification of gear-linkage tie-rod. Linear travel sensor kit works with bikes that have no shift rod, or on which the shift rod pressure/tension sensor will not fit. Mounts to the shift lever on one end and to a fixed point on the chassis on the other. Universal mounting kit included. DQS is compatible with all PCIIIUSB Power Commanders and plugs into the expansion port with no splicing or re-wiring required. Power Commander Control Center software allows the rider to adjust engine kill time during upshifts, and makes it possible to set minimum rpm engine speeds for system operation. To order either of the above sensors, the user must determine the correct direction of movement during the upshift (push or pull). If using the shift rod/pressure/tension sensor, press on the shift lever in the direction of an upshift and see if the rod is pushing or pulling on the clevis on the shift shaft. For the linear travel sensor, the shifter is also moved in the direction of an upshift. If the movement is down then a pull sensor is needed. If the movement is up a push sensor is required. . Power Commander PCII, PCIII and PCIIIr are not compatible with the DSQ. 4103 2 on hand
$109.99Dynojet Quick Shifter Handlebar Switch 4105
Manufacturer: Dynojet
Dennis Kirk Part #: 211045
Dynojet Quick Shifter Handlebar Switch: Manufacturer part # 4105 - Dynojet Quick Shifter allows the rider to make full-throttle, clutchless upshifts. Handlebar activation switch is used when a shift rod/lever mounted sensor is illegal for certain racing applications, impractical to fit on a specific model, or is not preferred by the rider. Handlebar switch requires the rider to lightly pre-load the shift lever, press the handlebar switch and complete the final shifter movement. Power Commander Control Center software lets the user control the amount of power interruption (shift kill time) and the minimum engine rpm at which the system will function. Power Commander PCII, PCIII and PCIIIr models cannot use Quick Shifter kits.. 4105 Expected Soon
$348.95Moose Quick Release EX Load Drop Rack 4165
Manufacturer: Moose
Dennis Kirk Part #: 514778
Moose Quick Release EX Load Drop Rack: Manufacturer part # 4165 - Increase the hauling capacity of your ATV by mounting our heavy-duty ex-load drop rack. Tailgate-style back door drops down for easy for easy loading and unloading. Drop rack can hold up to 3 five gallon buckets. Constructed from 3/4" square tubing and 14 gauge 1/2" metal mesh. Drop rack measures 41" W x 14" L x 11 1/2" D. Mount uses a receiver style system and comes with two mount kits. Baked high-gloss enamel powder-coated finish. Rack liner available separate, part# 49-0512. Drop rack may limit access to some storage compartments.. 4165 1 on hand
$45.99Pingel 1 in. Dia. Frame Tube Mount 62061
Manufacturer: Pingel
Dennis Kirk Part #: 491158
Pingel 1 in. Dia. Frame Tube Mount: Manufacturer part # 62061 - Use to mount Electric Shift Kits Part Numbers 271134, 271137, 271796, and 271797. 62061 1 on hand
$923.99Pingel Bolt-On Electric Shift Kit 77001
Manufacturer: Pingel
Dennis Kirk Part #: 271784
Pingel Bolt-On Electric Shift Kit: Manufacturer part # 77001 - A touch of the button eliminates the need to shift with your foot or clutch and provides lightning-fast gearshifts. Using these kits will not eliminate the need to use the clutch for starting and stopping. Button control for the state-of-the-art control module triggers the shift solenoid. Full-throttle up/down shifting made possible by the ignition kill box; also helps riders who have difficulty with stiff clutches by making use of the clutch for up and down shifts unnecessary. Bike-specific and universal kits include a stylish dual-button upshift/downshift control and a chrome-plated electronic shift solenoid. Bike-specific kits include all necessary mounting brackets. , , NOTE: This item ships 3 or 4 days after the order is placed.. 77001 1 on hand
$18.99Dynojet Female/Female Shift Rod A 32104060
Manufacturer: Dynojet
Dennis Kirk Part #: 270927
Dynojet Female/Female Shift Rod A: Manufacturer part # 32104060 - Dynojet Quick Shifter (DQS) allow you to make full-throttle, clutchless upshifts. Accessory kits include necessary pieces (such as shift rods) so you can install a DQS system without having to fabricate custom parts. Plugs into expansion port on Power Commander III USB module; no cutting or splicing of bikes wiring harness required. Included software lets you adjust amount of engine kill time and minimum engine operating rpm (keeps system from activating at too low of an rpm, such as low-speed road riding) Ideal for club racers, track day riders or even aggressive street riders. Bike-specific applications are designed for stock footrest assemblies using normal street-pattern shifting. Sensor and shift rod must be purchased separately. NOTE: The shift rod isnt required for the following models: Ducati Superbike 749/S 03-05, and the Ducati Superbike 999 03-05 NOTE: Your bike must have a Power Commander III USB module installed in order to use a Quick Shifter. Power Commander PCII, PCIII and PCIIIr modules cannot be used with a Quick Shifter. 32104060 4 on hand
Moose Extended Lift Push Tube
Vance & Hines Dresser Dual Header Pipes 16729
Motion Pro SyncPro Carburetor Tuner
Kuryakyn Wheel Chock 922
Vance & Hines Big Radius Exhaust 26029
Caliber Poly-Shield III Salt Shield 13401
Parts Unlimited Large Universal Cover CS-1002
Kuryakyn Condor Pit-Stop/Trailer Stop Wheel Chock 920
Parts Unlimited Total Cover TC-1005
Vance & Hines Straight Shot HS Slip-Ons 16819
Vance & Hines Big Shot Duals 17925
Caliber LowPro Low Profile Wide 8 in. Trailer Guide and Protection System 13322
HJC Electric Shield
Battery Tender Battery Tender Jr. 12-Volt Model
BUB Rinehart 3 1/2 in. Slip-On Mufflers
Kuryakyn GranTour Bag 4141
Vance & Hines Big Radius Exhaust 26003
NGK Resistor Spark Plug BR9ES
JPS Blue Polyurethane Fuel Line
HJC Universal Quick Release Buckle
RBI Inc Bearing OEM Standard No 62052RS
