|
|
|
|
|
|
|
|
$94.99
Full Throttle Inc. Goldfinger Left Hand Throttle Kit for Arctic Cat 0071021G
Manufacturer: Full Throttle Inc.
Dennis Kirk Part #: 198486
Full Throttle Inc. Goldfinger Left Hand Throttle Kit for Arctic Cat: Manufacturer part # 0071021G - Highest-quality stainless steel used in the cable adapter and fasteners. Installs over grip on most models; does not interfere with handwarmers. Throttle can be operated with one finger for safer sidehilling. Aluminum throttle lever features a gold anodized finish;. Rubber accordian boot keeps snow out of cable housing; safety pin locks left throttle from use while trailriding, etc.. Quick installation -- aproximately 20 minutes. Complete Kit includes all hardware, Allen wrenches and instructions. INCLUDED ITEMS: One perch with goldfinger lever. One handlebar spacer (clear vinyl tubing). One black cable housing. One stainless steel cable. One safety locking pin for throttle. One 2-1/4 in. ss allen bolt, w/ 4 flat washers and nyloc nut (replaces pivot pin). One stainless steel adapter plate for right side. One barrel bolt (looks like a bullet with a hole through the center) with ss allen screw and two ss washers for correct spacing. One aluminum cable crimp cap (don't lose it....its small). Four plastic zip-ties. Two allen wrenches (4mm, 5mm).. 0071021G
More than 10 on hand
More Info/Options for Full Throttle Inc. Goldfinger Left Hand Throttle Kit for Arctic Cat 0071021G
Kit Clutch Arctic Cat
|
|
|
|
|
|
$41.99
CMP Clutch Puller/Arctic Cat 80002230
Manufacturer: CMP
Dennis Kirk Part #: 28662
CMP Clutch Puller/Arctic Cat: Manufacturer part # 80002230 - Constructed of top quality materials for strength and durability. Machined to exacting tolerances. This puller is interchangeable with imported puller part NO. 28-655. CMP brand, made in the USA. , NOTE: For best results an anti-seize compound should be applied to the threads of the puller before use. See the Index in the back of this catalog.. 80002230
More than 10 on hand
More Info/Options for CMP Clutch Puller/Arctic Cat 80002230
Kit Clutch Arctic Cat
|
|
|
|
|
|
|
|
|
|
|
|
$14.99
Kimpex Tether Switch for Yamaha and 96-98 Arctic Cat ZR models 01-111-14
Manufacturer: Kimpex
Dennis Kirk Part #: 210033
Kimpex Tether Switch for Yamaha and 96-98 Arctic Cat ZR models: Manufacturer part # 01-111-14 - Disconnects ignition instantly when rider is separated from machine. Safety feature required by most racing organizations. Safety stop switch only; no tether included -- use PART NO. 21-214. This tether is normally open. To see if this is correct for your machine you must perform the following test. 1. Locate the two wires going to your machine's kill switch. 2. With the kill switch in the run position, test for continuity between the two wires. 3. If you DO NOT have continuity, this tether switch WILL work for your machine. 4. If you DO have continuity, this tether WILL NOT work for your machine, , NOTE: When selecting a kill switch be sure to check and see if you need a Normally Open or a Normally Closed switch. If you are not sure, check the wiring schematic for your machine. 01-111-14
More than 10 on hand
More Info/Options for Kimpex Tether Switch for Yamaha and 96-98 Arctic Cat ZR models 01-111-14
Kit Clutch Arctic Cat
|
|
|
|
$16.99
Kimpex Tether Switch for Arctic Cat 01-111-15
Manufacturer: Kimpex
Dennis Kirk Part #: 210034
Kimpex Tether Switch for Arctic Cat: Manufacturer part # 01-111-15 - Disconnects ignition instantly when rider is separated from machine. Safety feature required by most racing organizations. Safety stop switch only; no tether included -- use PART NO. 21-214. This tether is normally closed. To see if this is correct for your machine you must perform the following test. 1. Locate the two wires going to your machine's kill switch. 2. With the kill switch in the run position, test for continuity between the two wires. 3. If you DO have continuity, this tether switch WILL work for your machine. 4. If you DO NOT have continuity, this tether WILL NOT work for your machine, , NOTE: When selecting a kill switch be sure to check and see if you need a Normally Open or a Normally Closed switch. If you are not sure, check the wiring schematic for your machine. 01-111-15
More than 10 on hand
More Info/Options for Kimpex Tether Switch for Arctic Cat 01-111-15
Kit Clutch Arctic Cat
|
|
Moose Extended Lift Push Tube
Vance & Hines Dresser Dual Header Pipes 16729
Motion Pro SyncPro Carburetor Tuner
Kuryakyn Wheel Chock 922
Vance & Hines Big Radius Exhaust 26029
Caliber Poly-Shield III Salt Shield 13401
Parts Unlimited Large Universal Cover CS-1002
Kuryakyn Condor Pit-Stop/Trailer Stop Wheel Chock 920
Parts Unlimited Total Cover TC-1005
Vance & Hines Straight Shot HS Slip-Ons 16819
Vance & Hines Big Shot Duals 17925
Caliber LowPro Low Profile Wide 8 in. Trailer Guide and Protection System 13322
HJC Electric Shield
Battery Tender Battery Tender Jr. 12-Volt Model
BUB Rinehart 3 1/2 in. Slip-On Mufflers
Kuryakyn GranTour Bag 4141
Vance & Hines Big Radius Exhaust 26003
NGK Resistor Spark Plug BR9ES
JPS Blue Polyurethane Fuel Line
HJC Universal Quick Release Buckle
RBI Inc Bearing OEM Standard No 62052RS
