$24.99Chatterbox Power Cord 4 Feet Coiled CBFRSPREX
Manufacturer: Chatterbox
Dennis Kirk Part #: 40588
Chatterbox Power Cord 4 Feet Coiled: Manufacturer part # CBFRSPREX - Work with the FRS X2, GMRS X1, and HJC-FRS Communitcators. 4 foot cord to wire to your vehicle's 12V electrical system. CBFRSPREX 5 on hand
$12.95HJC Electric Shield Replacement Power Cord Set ELECTRIC CORD
Manufacturer: HJC
Dennis Kirk Part #: 323865
HJC Electric Shield Replacement Power Cord Set: Manufacturer part # ELECTRIC CORD - For use with HJC electric shields. This replacement cord set is for the HJC FG Tech, Cl-11/Checker Snow, CL-10, FG-9, FG-10, LS Airtech, ZF-7, CS-10 helmets. Also works with electric shields on Z1R Stance and Strike helmets. , Included Items: , One battery power cord, One shield power cord, One short connector cord, Two short plastic tie straps, One long plastic tie strap. ELECTRIC CORD More than 10 on hand
$24.99Chatterbox Power Cord for FRS X2 Communicator CBXPREX
Manufacturer: Chatterbox
Dennis Kirk Part #: 40717
Chatterbox Power Cord for FRS X2 Communicator: Manufacturer part # CBXPREX - Works with the FRS X2 or GMRS X1 Communitcators. Power cord to wire communicator to your vehicles 12-volt electrical system.. CBXPREX 8 on hand
$18.99Gears Coiled Switch Cord For Gen X/X-2 Heated Vests 1001451
Manufacturer: Gears
Dennis Kirk Part #: 201841
Gears Coiled Switch Cord For Gen X/X-2 Heated Vests: Manufacturer part # 1001451 - Replacement 30" (expands to 45") coiled switch cord for Gen X and X-2 heated vests. 1001451 2 on hand
$18.99Gears Coiled Extension Cord For Gen X/X-2 Apparel 1001501
Manufacturer: Gears
Dennis Kirk Part #: 201855
Gears Coiled Extension Cord For Gen X/X-2 Apparel : Manufacturer part # 1001501 - For use with Gen X and X-2 heated vests or Gen X leg chaps. Increases the distance between the controller and vest or between vehicle and controller with the coiled extension cord; stretches from 17" to 35".. 1001501 2 on hand
$4.99Power Cord Holder for HJC 836-362
Manufacturer: HJC
Dennis Kirk Part #: 324873
Power Cord Holder for HJC: Manufacturer part # 836-362 - Electric Shield Power Cord Holder for all HJC helmets except CS-R1. 836-362 More than 10 on hand
$37.99EXO-2 12 Volt Accessory Socket Power Cord p208919
Manufacturer: EXO-2
Dennis Kirk Part #: 208919
EXO-2 12 Volt Accessory Socket Power Cord: Manufacturer part # p208919 - For use to power the EXO-2 vests, jacket and back support via a vehicle accessory outlet.. p208919 1 on hand
$12.99HJC CS-R1 Series Power Cord 806-360
Manufacturer: HJC
Dennis Kirk Part #: 32327041
HJC CS-R1 Series Power Cord: Manufacturer part # 806-360 -. 806-360 1 on hand
$7.99HJC CS-R1S Power Cord Holder 152-362
Manufacturer: HJC
Dennis Kirk Part #: 32327042
HJC CS-R1S Power Cord Holder: Manufacturer part # 152-362 -. 152-362 6 on hand
$3.99HJC CS-R1S Power Cord Holder Bolt 805-372
Manufacturer: HJC
Dennis Kirk Part #: 32327047
HJC CS-R1S Power Cord Holder Bolt: Manufacturer part # 805-372 -. 805-372 6 on hand
$89.99Accel Power Pulse Coil 140402
Manufacturer: Accel
Dennis Kirk Part #: 20308
Accel Power Pulse Coil: Manufacturer part # 140402 - Higher voltage. Faster rise time. Longer spark duration. Vibration and heat resistant. Accepts 7mm or 8mm wires. Designed for all 12-Volt ignition systems. Bright Accel yellow finish. , NOTE: Fits all points-triggered FL/FX/XL 65-77 models and all electronic ignition FL/FX and XL 78-83 models. 140402 3 on hand
$151.99Dynatek 0.5 Ohms Dual Output Miniature Coils DC111
Manufacturer: Dynatek
Dennis Kirk Part #: 201184
Dynatek 0.5 Ohms Dual Output Miniature Coils: Manufacturer part # DC111 - Designed for use with the Dyna TC88 series ignitions or factory-installed electronic ignitions that use low-resistance coils. Dual output for dual plug heads Sold in pairs , , NOTE: Must not be used with ignitions that are not specifically designed to use low-resistance coils.. DC111 1 on hand