Battery Hold Down

$21.99 Snobug 5000 lbs. Recessed Cargo Hold-Downs 40712
Dennis Kirk Part #: 40712
Snobug 5000 lbs. Recessed Cargo Hold-Downs 40712: Manufacturer part # THD700 - Inexpensive way to make trailering almost anything easier and safer. Made from tough steel with a rust-resistant zinc plating. Recessed hold-downs fit into pocket in trailer bed; can be bolted down or welded into place. Measures 4 1/2 in. x 5 in. and fits into a 3 1/2 in. dia. x 1 in. deep pocket; pull limit of 5000 lbs.. Drain hole in the base. Sold in pairs.. THD700
10+ on hand

More Info/Options for Snobug 5000 lbs. Recessed Cargo Hold-Downs 40712

$105.99 Fulton ATV Lock and Hold Down System 40545
Dennis Kirk Part #: 40545
Fulton ATV Lock and Hold Down System 40545: Manufacturer part # ATVC0100 - Quick and easy-to-use ratchet adjuster. Provides maximum safety and security. Eliminates the need for straps and tie-downs. Holds vehicle tight to trailer during transport. Keyed mechanism helps deter theft. Will not cause damage to vehicle or trailer. Includes "S" hooks with integrated locks and two tie-down plates for trailer bed.. ATVC0100
5 on Hand

More Info/Options for Fulton ATV Lock and Hold Down System 40545

$14.99 Snobug 750 lbs Cargo Surface-Mount Hold-Downs - 4 Pack 406790
Dennis Kirk Part #: 406790
Snobug 750 lbs Cargo Surface-Mount Hold-Downs - 4 Pack 406790: Manufacturer part # THD600 - Inexpensive way to make trailering almost anything easier and safer. Made from tough steel with a rust-resistant zinc plating. Surface-mount hold-downs fit anywhere flat. Measures 2 5/16 in. x 1 1/4 in.; pull limit of 750 lbs. Sold in a pack of four.. THD600
10+ on hand

More Info/Options for Snobug 750 lbs Cargo Surface-Mount Hold-Downs - 4 Pack 406790

$13.99 Snobug 1200 lbs. Recessed Cargo Hold-Downs. 40662
Dennis Kirk Part #: 40662
Snobug 1200 lbs. Recessed Cargo Hold-Downs. 40662: Manufacturer part # THD500 - Inexpensive way to make trailering almost anything easier and safer. Made from tough steel with a rust-resistant zinc plating. Recessed hold-downs fit into pocket in trailer bed; can be bolted down or welded into place. Measures 5 in. x 3.5 in. and fits into a 3 in. dia. x 5/16 in. deep pocket; pull limit of 1200 lbs.. Drain hole in the base. Sold in pairs.. THD500
10+ on hand

More Info/Options for Snobug 1200 lbs. Recessed Cargo Hold-Downs. 40662

$14.99 Snobug 1500 lbs. Round Surface-Mount Cargo Hold-Downs 407466
Dennis Kirk Part #: 407466
Snobug 1500 lbs. Round Surface-Mount Cargo Hold-Downs 407466: Manufacturer part # 39200069 - Inexpensive way to make trailering almost anything easier and safer. Made from tough steel with a rust-resistant zinc plating. Round, protected surface-mount style surrounded by plastic ramped bodies. Measures 4 1/8in. dia. x 1/2in. H with a .25in. dia. D-ring; pull limit is 1,500 lb.. Drain hole in the base. Sold in pairs.. 39200069
10+ on hand

More Info/Options for Snobug 1500 lbs. Round Surface-Mount Cargo Hold-Downs 407466

$16.95 H50092 Drag Specialties Quick Release Seat Hold Down Knobs
Dennis Kirk Part #: H50092
H50092 Drag Specialties Quick Release Seat Hold Down Knobs: Manufacturer part # 902132SC1 - Takes the hassle out of removing your seat. Polished, knurled aluminum seat hold-down knobs for Corbin seats. Thumbscrews feature recessed O-rings to protect the finish on the seat tab, and each has one short 1/4 in. -28 stud and one long 1 1/4 in.-20 stud. , NOTE: Seat tab cover not included. 902132SC1
3 on Hand

More Info/Options for H50092 Drag Specialties Quick Release Seat Hold Down Knobs

$12.99 H27138 Landmark Seat Hold Down Repair Kit
Dennis Kirk Part #: H27138
H27138 Landmark Seat Hold Down Repair Kit: Manufacturer part # LM00057 - Stainless steel kit is polished to a brilliant shine. Simple installation; just drill out old stripped threads, insert new bolt and lock down with nylon insert nut. Made in the U.S.A... LM00057
10+ on hand

More Info/Options for H27138 Landmark Seat Hold Down Repair Kit

$17.99 Kimpex Hood Hold Down Strap Kit 27815
Dennis Kirk Part #: 27815
Kimpex Hood Hold Down Strap Kit 27815: Manufacturer part # 32-360 - Keep quick-remove hoods in place or when additional tie-downs are required for racing. Sold in a kit that includes 1 tie-down, 1 hook, 1 cherry mate and rivets.. 32-360
4 on Hand

More Info/Options for Kimpex Hood Hold Down Strap Kit 27815

$69.99 Battery Tender International Battery Tender Plus 281873
Dennis Kirk Part #: 281873
Battery Tender International Battery Tender Plus 281873: Manufacturer part # INTL BATTERY TEN - Programmed to monitor the new sealed maintenance-free AGM (Absorbed Glass Matte) batteries. 12V-1.25A battery charger with an input voltage range of 100-240V. High-frequency design offers cooler and more efficient operation. Fully automatic constant charging consists of initialization, bulk, absorption and float/maintenance. Converts to float charger and monitors battery at 13.2 volts once a full charge is reached. Temperature compersation sensor is new and improved to adjust voltage for extreme heat or cold. Water-resistant, lightweight and compact. Comes with accessory pouch.. INTL BATTERY TEN
5 on Hand

More Info/Options for Battery Tender International Battery Tender Plus 281873

$30.99 Battery Tender Battery Tender Jr. 6-Volt Model 28764
Dennis Kirk Part #: 28764
Battery Tender Battery Tender Jr. 6-Volt Model 28764: Manufacturer part # BATTERY TENDER J - Two-stage, fully automatic battery charger. Suitable for lead-acid, sealed maintenance-free and gel cell batteries. Smart trickle charger maintains battery when charging process is finished. Lightweight and compact -- perfect for use when space is limited. Two-color LED indicator. Reverse polarity protection. Comes with both 12 output cord and quick-connect/disconnect snapcord. Two-year manufacturers warranty.. BATTERY TENDER J
9 on Hand

More Info/Options for Battery Tender Battery Tender Jr. 6-Volt Model 28764

$59.99 Battery Tender Battery Tender Plus - 6V/1.25 Amps 281822
Dennis Kirk Part #: 281822
Battery Tender Battery Tender Plus - 6V/1.25 Amps 281822: Manufacturer part # BATTERY TENDER P - Now you can constantly monitor a battery without the damaging effects of trickle chargers that eventually boil dry or overcharge batteries A charge cycle initially brings the battery to a full charge at approximately 14.2 volts. After the battery is fully charged, the Battery Tender Plus converts to a float charger and monitors the battery at 13.2 volts. Some periodic maintenance is recommended, but Battery Tender Plus will monitor a battery for years without boiling or destroying it. Features new fused quick disconnect rings with a weather cover. This has 1.25 amps. , , NOTE: Earlier model Battery Tenders have a WHITE snap cord connector; later models have a BLACK snap connector. These snap cords are NOT interchangeable.. BATTERY TENDER P
7 on Hand

More Info/Options for Battery Tender Battery Tender Plus - 6V/1.25 Amps 281822

$30.99 Battery Tender Battery Tender Jr. 12-Volt Model 28765
Dennis Kirk Part #: 28765
Battery Tender Battery Tender Jr. 12-Volt Model 28765: Manufacturer part # BATTERY TENDER J - Two-stage, fully automatic battery charger. Suitable for lead-acid, sealed maintenance-free and gel cell batteries. Smart trickle charger maintains battery when charging process is finished. Automatically converts to float charger, monitoring battery at 13.2 volts once 14.4 VDC charge is attained. Should battery drop below 12.6 volts, full charging resumes until 14.4 VDC is reached again -- battery is always ready to go. Lightweight and compact -- perfect for use when space is limited. Two-color LED indicator. Reverse polarity protection. Comes with both 12 output cord and quick-connect/disconnect snapcord. Two-year manufacturers warranty.. BATTERY TENDER J
10+ on hand

More Info/Options for Battery Tender Battery Tender Jr. 12-Volt Model 28765

Battery Hold Down