|
|
|
|
|
|
$84.99
Hot Rods Connecting Rod Kits 149145
Dennis Kirk Part #: 149145
Hot Rods Connecting Rod Kits 149145: Manufacturer part # 8607 - High-quality replacement kit features double rod life over OEM rods. Forged 8620 AISI steel rods. Less friction than conventional bearings -- double silver-coated rod bearings stand up to longer periods of non-lubrication. Kits include rod, crankpin, rod bearing and thrust washers.. 8607
1 on Hand
More Info/Options for Hot Rods Connecting Rod Kits 149145
|
|
|
|
$51.99
7/16 in./5/16 in./Wear Rod - Carbide/Pair Roetin Performance X-10 Two Carbide Wear Rods
Dennis Kirk Part #: 032024
7/16 in./5/16 in./Wear Rod - Carbide/Pair Roetin Performance X-10 Two Carbide Wear Rods: Manufacturer part # X102262 - Six inches of 90 degree carbide on 7/16 in. bar. Two carbide wear pads. Hardweld filler, complete. NOTE: Some models require drilling extra hole(s) in skis to mount carbides. Dennis Kirk recommends removing any paint from the studs before use by wire-brushing. NOTE: Some of the models listed have EZ Steer as original equipment, which is retained with the installation of any X-10 One or X-PR One carbides. If you wish to eliminate the original plate and 2-stud, 14 3/4 in. wear rods you may replace them with an X-10 One or X-PR One 3-stud, 27 1/2 in. type. NOTE: Not for 2002 models with dual rods on one ski. DIMENISIONS: Length X Diameter: 27" X 7/16". Stud Length X Diameter: 1-3/4" X 5/16". Number of studs: 4. Stud center mounting distance from: Front to 1st: 8-1/8". 1st to 2nd: 3 7/8". 2nd to third: 7". LI> 3rd to 4th: 7". 1st to 2nd: 3 7/8". Fourth to end: 1".. X102262
2 on Hand
More Info/Options for 7/16 in./5/16 in./Wear Rod - Carbide/Pair Roetin Performance X-10 Two Carbide Wear Rods
|
|
|
|
$75.99
1/2 in./6 in./3/8 in./Wear Rod - Carbide/Pair Woodys Executive Series Carbide Wear Rods
Dennis Kirk Part #: 032012
1/2 in./6 in./3/8 in./Wear Rod - Carbide/Pair Woodys Executive Series Carbide Wear Rods: Manufacturer part # WPI-1125 - Top-Stock hardweld runner (no carbide) designed for extreme service. A full range of carbide wear rod choices for the casual trail rider to the serious rider with a heavily studded track and even for Snocross competition. Carbide types prevent the rear of higher horsepower performance machines from "pushing" the front, especially on icy trails. Special Shur-Steer carbide designs for Polaris with E-Z Steer. Flat-Top host rods on all types for greater support between runner and ski. See separate descriptions for amount of center turning carbide, carbide wear pads and full-length hardweld filler for durability. All studs are long enough for ski skins. Rears are angle-cut for easier unloading and backing up. Sold in pairs; fastening nuts included NOTE Designed for performance trail riders and cross-country racers . 8 inch of 60 degree carbide with front and rear wear pads. Full-length hardweld between carbide inserts. 1/2 inch diameter host bar, 3/8 inch studs. , Dimensions:, Length x Diameter: 17-1/2in. x 3/8in., Stud Diameter x Length: 5/16in. x 1-1/8in., Number of Studs: 3. Stud Center Mounting Distance From:, Front to 1st: 3-1/4in., 1st to 2nd: 7-1/8in., 2nd to 3rd: 4-1/8in., 3rd to End: 2in.. Color:Black.. WPI-1125
2 on Hand
More Info/Options for 1/2 in./6 in./3/8 in./Wear Rod - Carbide/Pair Woodys Executive Series Carbide Wear Rods
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
