$229.99JIMS Mainshaft for 5-Speed Transmissions 35042-91
Manufacturer: JIMS
Dennis Kirk Part #: H14195
JIMS Mainshaft for 5-Speed Transmissions: Manufacturer part # 35042-91 - Sold individually. Replaces OEM number 35042-91.. 35042-91 1 on hand
$207.99Wild 1 Inc. Chubby 9.5 in. Springer Ape Hanger Bar WO514
Manufacturer: Wild 1 Inc.
Dennis Kirk Part #: 595075
Wild 1 Inc. Chubby 9.5 in. Springer Ape Hanger Bar: Manufacturer part # WO514 - These 1 1/4 in. diameter handlebars are 25% thicker than stock handlebars. Designed with fluid bends at precise angles to provide maximum comfort and control. Pre-drilled for internal wiring and feature a dimpled and diamond knurled design in a show-chromed finish. Work with stock and most custom controls, stock risers and top clamps. Made in the U.S.A.. Bar is drilled and knurled. Knurling is 5 in. on center. , , Width: 37 1/2". , Rise: 10 1/4". , Pullback: 9 1/4". , Center Width: 10". , End Rise: 10 3/4". , 1" Diameter Clamping Width: 2/2". , Inside Width of Knurling/Outside: 3 1/4"/6 1/4". , Drilled for Internal Wiring: Yes. , Dimpled to Prevent Pinching Control Wires: Yes. , Three Notches for 08-up H-D W/Electronic Throttle: No.. WO514 1 on hand
$232.95Drag Specialties 9.5 in. Ape Hanger Flame 1 1/4 in. Tattoo Handlebar for Springer pH59150
Manufacturer: Drag Specialties
Dennis Kirk Part #: H59150
Drag Specialties 9.5 in. Ape Hanger Flame 1 1/4 in. Tattoo Handlebar for Springer: Manufacturer part # pH59150 - Chromed handlebars with an engraved flame design on exposed sections. Work with standard controls; drilled for internal wires. Finish is brilliant show chrome. Springer-style bars have the area between the risers increased to 1 1/4 in. for a smooth finished look; work with the OEM Springer risers and handlebar clamps. Billet gauge mounts for T-Bars are available separately in three styles. 1 1/4 in. thick risers are also available to complete the Buffalo look. Made in the U.S.A., , Diameter Clamping Width: 6-3/4 in., Inside Width of Knurling/Outside: 4-1/16 in. / 5-7/16 in., Drilled for Internal Wiring: Yes. , , Note: Hydraulic clutch master cylinder may not fit handlebars larger than 1 in. diameter, , NOTE: Will not fit Touring 08-09 models. pH59150 2 on hand
$232.95Drag Specialties 9.5 in. Ape Hanger Flame 1 1/4 in. Tattoo Handlebar pH59149
Manufacturer: Drag Specialties
Dennis Kirk Part #: H59149
Drag Specialties 9.5 in. Ape Hanger Flame 1 1/4 in. Tattoo Handlebar: Manufacturer part # pH59149 - Chromed handlebars with an engraved flame design on exposed sections. Work with standard controls; drilled for internal wires. Finish is brilliant show chrome. Billet gauge mounts for T-Bars are available separately in three styles. 1 1/4 in. thick risers are also available to complete the Buffalo look. Handlebar clamps cover all of the center area that is sized down to 1 in. (not available for Springer models). Made in the U.S.A., , 1" Diameter Clamping Width: 5-1/8 in., Inside Width of Knurling/Outside: 2-3/4 in. / 4-1/4 in., Drilled for Internal Wiring: Yes.. , , NOTE: Not for use with stock risers and handlebar/gauge mount clamp on 883/1200 models. , , Note: Hydraulic clutch master cylinder may not fit handlebars larger than 1 in. diameter, , NOTE: Will not fit Touring 08-09 models. pH59149 1 on hand
$79.95Harley-Davidson Fat Boy Windshield Bag 58307-95
Manufacturer: Harley-Davidson
Dennis Kirk Part #: 506792
Harley-Davidson Fat Boy Windshield Bag: Manufacturer part # 58307-95 - This windshield bag, designed to match the Fat Boy seat and tank panel, is made of black domestic steerhide. Features an embossed Fat Boy logo and hand-laced leather lid. , NOTE: Fits King-Size windshields (except Nostalgic, Flame, and Skull with Wings King-Size), and Compact windshields (except FXSTD, Flame and Skull with Wings). Does not fit 100th Anniversary logo windshields, models equipped with handlebar mount gauges, or Road Tech Riser Mount Radio.. 58307-95 1 on hand
$79.95Harley-Davidson Embossed Bar and Shield Logo Windshield Bag 58308-95
Manufacturer: Harley-Davidson
Dennis Kirk Part #: 506790
Harley-Davidson Embossed Bar and Shield Logo Windshield Bag: Manufacturer part # 58308-95 - Styling details include embossed Bar and Shield logo. Fabricated of black domestic steerhide. , NOTE: Fits King-Size windshields (except Nostalgic, Flame, and Skull with Wings King Size), and Compact windshields (except FXSTD, Flame, and Skull with Wings). Does not fit 100th Anniversary logo windshields, models equipped with handlebar mount gauges, or Road Tech Riser Mount Radio.. 58308-95 3 on hand
$37.99JIMS Clutch Spring Compressor Nut Tool 38515-91
Manufacturer: JIMS
Dennis Kirk Part #: H28129
JIMS Clutch Spring Compressor Nut Tool: Manufacturer part # 38515-91 - Releases the clutch spring, making it easier to remove and install the retaining ring. When using on XL 91-06 models, H28-129 compressor nut must be used in conjunction with H28-208 compressor tool (sold separately).. 38515-91 3 on hand
$61.99SLP Brake Line 27-95
Manufacturer: SLP
Dennis Kirk Part #: 198481
SLP Brake Line: Manufacturer part # 27-95 - Out-perform 40 inch length rubber, braided cord or metal lines. Lightweight and flexible lines with a burst strength of 12,000 lb.. Reduces braking effort due to up to 70 percent less expansion. Operating range from -67 degree to 464 degree.. 27-95 2 on hand
$64.95Drag Specialties 2:1 FL-Style Speedometer with 89-95 Face DS243845
Manufacturer: Drag Specialties
Dennis Kirk Part #: 407167
Drag Specialties 2:1 FL-Style Speedometer with 89-95 Face: Manufacturer part # DS243845 - Will fit FL 81-84, XL 52-94, FX and FXR 73-94 models with front-wheel drive speedometer and FL-style dash; will also fit FL 47-61 with transmission-drive speedometer and FL-style dash. Also available is a model with built-in electronic 12V tachometer. Features 12mm thread, trip reset knob and gasket. To install these speedo heads on FL 47-61, use our cable adapter PART NO. H40-0152.. DS243845 3 on hand
$179.95Drag Specialties Dual Gauge Mount for 95-08 Style Gauges pH59362
Manufacturer: Drag Specialties
Dennis Kirk Part #: H59362
Drag Specialties Dual Gauge Mount for 95-08 Style Gauges: Manufacturer part # pH59362 - Billet gauge mount for 1-1/4" T-bars. Made in the U.S.A... pH59362 1 on hand
CLEARANCE!
Was: $1995.99
Now: $1496.99
Kuryakyn Wild Things Forged Cylinder Heads For 95 and 103 cu. in. Twin Cam Motors 434
Manufacturer: Kuryakyn
Dennis Kirk Part #: 149468
Kuryakyn Wild Things Forged Cylinder Heads For 95 and 103 cu. in. Twin Cam Motors: Manufacturer part # 434 - Kuryakyn is proud to offer forged versions of our cutting-edge billet cylinder heads. Efficient, bathtub combustion chambers. Set to take cams of up to .640" lift. Proprietary valves designed on the flow bench to match Wild Things ports. Hard valve seats for use with lead-free fuel. Intake ports: 3/8" raised high flow and high velocity with 1.980" stainless intake valves. Exhaust ports: constant-radius "D" high flow and high velocity with 1.630" stainless steel exhaust valves. High-performance valve springs and titanium top retainers. Balances awesome horsepower and torque with the qualities of a good street motor. Starts as easy as a stock bike, runs on pump gas without any detonation, runs cooler than stock and is as tractable as a stock bike. Come completely assembled and ready to install; require the purchase of four long OEM headbolts for installation (sold separately)-16478-85A. Utilizes equal-length head bolts to minimize cylinder distortion and promote consistent head gasket squish. Extra cooling fin area. Larger, improved breather passages (requires crankcase breather kit with 1/2" -13 breather bolts. Larger, relocated oil drains. All stock parts will mount to forged heads. , Gaskets available separately: , .030 Head Gasket 26-3260, .045 Head Gaskets 26-3261, .051 Head Gaskets 26-3262, .060 Head Gaskets 26-3263, Exhaust Gaskets 26-3259, , NOTE: For use with flat-top pistons 14-9351, 14-9352 or 14-9354; 81cc combustion chambers. Yields 9.5:1 compression ratio in 95" applications. Yields 10.5:1 compression ratio in 103" applications, , Note: Finish is Bright Bead Blast. 434 1 on hand
CLEARANCE!
Was: $329.99
Now: $247.49
Kuryakyn Wild Things Flat Top Piston Kit for 95 in. Twin Cam - (3.875 in. bore) 446
Manufacturer: Kuryakyn
Dennis Kirk Part #: 149351
Kuryakyn Wild Things Flat Top Piston Kit for 95 in. Twin Cam - (3.875 in. bore): Manufacturer part # 446 - They are forged from the highest-grade aluminum alloy designed for piston use making them the strongest piston on the market for your 95 in. Twin Cam. The special skirt shape and material means less break-in time, quieter running and a stronger resistance to scoring. The lightweight design results in less power robbed by the forces of inertia and less vibration. Larger and deeper valve pockets will handle larger valves and cams without extra machine work. The decks are slightly raised for a tight squish with stock .045'' thick head gaskets. This is extremely important and results in better combustion efficiency and power. The redesigned dome shape on the high-Compression piston for stock heads results in less pumping losses and better combustion efficiency and detonation controls. Kit complete with pistons, rings, circlips and wrist pin.. 446 1 on hand
Moose Extended Lift Push Tube
Vance & Hines Dresser Dual Header Pipes 16729
Motion Pro SyncPro Carburetor Tuner
Kuryakyn Wheel Chock 922
Vance & Hines Big Radius Exhaust 26029
Caliber Poly-Shield III Salt Shield 13401
Parts Unlimited Large Universal Cover CS-1002
Kuryakyn Condor Pit-Stop/Trailer Stop Wheel Chock 920
Parts Unlimited Total Cover TC-1005
Vance & Hines Straight Shot HS Slip-Ons 16819
Vance & Hines Big Shot Duals 17925
Caliber LowPro Low Profile Wide 8 in. Trailer Guide and Protection System 13322
HJC Electric Shield
Battery Tender Battery Tender Jr. 12-Volt Model
BUB Rinehart 3 1/2 in. Slip-On Mufflers
Kuryakyn GranTour Bag 4141
Vance & Hines Big Radius Exhaust 26003
NGK Resistor Spark Plug BR9ES
JPS Blue Polyurethane Fuel Line
HJC Universal Quick Release Buckle
RBI Inc Bearing OEM Standard No 62052RS
