|
|
$789.99
H18832 Independent Gas Tank Company Stretch Tanks
Dennis Kirk Part #: H18832
H18832 Independent Gas Tank Company Stretch Tanks: Manufacturer part # CS2 - Handcrafted tank is quality constructed using 16-gauge cold-rolled steel. Each tank has been TIG welded, then pressure tested to the highest standards. Has four mounts on the tank bottom and a tunnel width of 2 1/4 in.. 22mm petcock fitting. 1/8" NPT threaded crossover fittings. Require custom mounting; will not work on frames with standard Fat Bob tank mounts. Made in the U.S.A., , TANK STYLE - Chopper. 11" wide with square end. Capacity is approximately 3.7 gal.. 25" L X 11" W. Screw-in cap Bung, , NOTE: Not for use on fuel-injected models, , NOTE: The use of a custom seat is required, , NOTE: Tanks with screw-in caps use 82-E96 style caps (sold separately), , NOTE: This item ships 3-4 days after order is placed, , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. CS2
1 on Hand
More Info/Options for H18832 Independent Gas Tank Company Stretch Tanks
|
|
|
|
$789.99
H18830 Independent Gas Tank Company Stretch Tanks
Dennis Kirk Part #: H18830
H18830 Independent Gas Tank Company Stretch Tanks: Manufacturer part # 07010006 - Handcrafted tank is quality constructed using 16-gauge cold-rolled steel. Each tank has been TIG welded, then pressure tested to the highest standards. Has four mounts on the tank bottom and a tunnel width of 2 1/4 in.. 22mm petcock fitting. 1/8" NPT threaded crossover fittings. Require custom mounting; will not work on frames with standard Fat Bob tank mounts. Made in the U.S.A., , TANK STYLE - Chopper. 11" wide with square end and rounded sides. Capacity is approximately 3.7 gal.. 25" L X 11" W. Screw-in cap Bung, , NOTE: Not for use on fuel-injected models, , NOTE: The use of a custom seat is required, , NOTE: Tanks with screw-in caps use 82-E96 style caps (sold separately), , NOTE: This item ships 3-4 days after order is placed, , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. 07010006
1 on Hand
More Info/Options for H18830 Independent Gas Tank Company Stretch Tanks
|
|
|
|
$789.99
Independent Gas Tank Company 4 in Stretch Bobber Tank w/ Pointed End and Screw-in Cap 182579
Dennis Kirk Part #: 182579
Independent Gas Tank Company 4 in Stretch Bobber Tank w/ Pointed End and Screw-in Cap 182579: Manufacturer part # BOBBER - Handcrafted tanks are quality constructed using 16-gauge cold-rolled steel. Each tank has been TIG welded, then pressure tested to the highest standards. All styles have four mounts on the tank bottom and all but Bobber have tunnel width of 2 1/4". Bobber tanks feature a tunnel width of 2 1/2". Other features include: 22mm petcock fitting, 1/8" NPT threaded crossover fittings and screw-in cap or Hot Match pop-up flush cap. Custom mounting required; will not fit frames with standard Fat Bob tank mounts. Made in the U.S.A.. Bobber: square 2 1/4" at the rear or pointed end. , NOTE: The use of a custom seat is required, , NOTE: Tanks with screw bungs use 82-E96 style caps (sold separately), , NOTE: This items ships 3-4 days after order is placed, , WARNING: , All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems. BOBBER
1 on Hand
More Info/Options for Independent Gas Tank Company 4 in Stretch Bobber Tank w/ Pointed End and Screw-in Cap 182579
|
|
|
|
$789.99
Independent Gas Tank Company 4 in Stretch Bobber Tank w/ Square End and Screw-in Cap 182577
Dennis Kirk Part #: 182577
Independent Gas Tank Company 4 in Stretch Bobber Tank w/ Square End and Screw-in Cap 182577: Manufacturer part # BOBBER - Handcrafted tanks are quality constructed using 16-gauge cold-rolled steel. Each tank has been TIG welded, then pressure tested to the highest standards. Four mounts on the tank bottom and feature a tunnel width of 2 1/2". Other features include: 22mm petcock fitting, 1/8" NPT threaded crossover fittings and screw-in cap bung. Custom mounting required; will not fit frames with standard Fat Bob tank mounts. Made in the U.S.A. Tank Syle - Bobber: square 2 1/4" end, , NOTE: The use of a custom seat is required, , NOTE: Tanks with screw bungs use 82-E96 style caps (sold separately), , NOTE: This item is shipped 3-4 days after the order is placed, , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. BOBBER
1 on Hand
More Info/Options for Independent Gas Tank Company 4 in Stretch Bobber Tank w/ Square End and Screw-in Cap 182577
|
|
|
|
|
|
$789.99
D&D 2-into-1 Fat Cat Pipes 251470
Dennis Kirk Part #: 251470
D&D 2-into-1 Fat Cat Pipes 251470: Manufacturer part # 649503 - These are D&D's best performing pipes and the winner of Cycle World Magazines 2002 Power and Performance exhaust shootout. Just bolt them on and see gains of as much as 25 percent more horsepower and 15 percent more torque than stock. 2-into-1 design with stepped head pipes for maximum performance. 3/4 wrap heat shields to maintain appearance, and back-cut ends. , NOTE: There is no warranty on exhaust pipes and mufflers with regard to any discoloration. Discoloration (blueing)is the result of tuning characteristics, cam timing, carburetor jetting, overheating,etc. and is not caused by defective manufacturing., , See lubrication products for products that will help prevent or remove blueing.. 649503
Expected Soon
More Info/Options for D&D 2-into-1 Fat Cat Pipes 251470
|
|
|
|
$789.99
H18844 Independent Gas Tank Company 2 in. Stretch Tank
Dennis Kirk Part #: H18844
H18844 Independent Gas Tank Company 2 in. Stretch Tank: Manufacturer part # 19140132 - 2.5 gallon tank. Tank is 22 in. L x 11 in. W. Handcrafted tank is quality constructed using 16-gauge cold-rolled steel. Each tank has been TIG welded, then pressure tested to the highest standards. Has four mounts on the tank bottom and a tunnel width of 2 1/4 in.. Other features include: 22mm petcock fitting, threaded crossover fittings and screw-style bung or HotMatch pop-up flush cap. Custom mounting required; will not fit frames with standard Fat Bob tank mounts. Made in the U.S.A.. , Tank Style-Straight-Up: Point end; use screw-in cap, , NOTE: The use of a custom seat is required, , NOTE: Tanks with screw bungs use 82-E96 style caps, , NOTE: This item ships 3-4 days after order is placed, , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. 19140132
1 on Hand
More Info/Options for H18844 Independent Gas Tank Company 2 in. Stretch Tank
|
|
|
|
$789.99
H18836 Independent Gas Tank Company Stretch Tanks
Dennis Kirk Part #: H18836
H18836 Independent Gas Tank Company Stretch Tanks: Manufacturer part # 19140130 - Handcrafted tank is quality constructed using 16-gauge cold-rolled steel. Each tank has been TIG welded, then pressure tested to the highest standards. Has four mounts on the tank bottom and a tunnel width of 2 1/4 in.. 22mm petcock fitting. 1/8" NPT threaded crossover fittings. Require custom mounting; will not work on frames with standard Fat Bob tank mounts. Made in the U.S.A., , TANK STYLE - Aero. Pointed at the rear. Notched for seat tube clearance. Capacity is approximately 4 gal.. 22" L X 13" W. Matt Hotch pop-up cap, , NOTE: Not for use on fuel-injected models, , NOTE: The use of a custom seat is required, , NOTE: This item ships 3-4 days after order is placed, , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. 19140130
1 on Hand
More Info/Options for H18836 Independent Gas Tank Company Stretch Tanks
|
|
|
|
$789.99
H18856 Independent Gas Tank Company Stretch Tanks
Dennis Kirk Part #: H18856
H18856 Independent Gas Tank Company Stretch Tanks: Manufacturer part # DS391717 - Handcrafted tank is quality constructed using 16-gauge cold-rolled steel. Each tank has been TIG welded, then pressure tested to the highest standards. Has four mounts on the tank bottom and a tunnel width of 2 1/4 in.. 22mm petcock fitting. 1/8" NPT threaded crossover fittings. Require custom mounting; will not work on frames with standard Fat Bob tank mounts. Made in the U.S.A., , TANK STYLE - Aero. Pointed at the rear Notched for seat tube clearance. Capacity is approximately 5 gal.. 25" L X 14" W. Screw-in cap bung, , NOTE: Not for use on fuel-injected models, , NOTE: The use of a custom seat is required, , NOTE: Tanks with screw-in caps use 82-E96 style caps (sold separately), , NOTE: This item ships 3-4 days after order is placed, , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. DS391717
1 on Hand
More Info/Options for H18856 Independent Gas Tank Company Stretch Tanks
|
|
|
|
$789.99
H18825 Independent Gas Tank Company Stretch Tanks
Dennis Kirk Part #: H18825
H18825 Independent Gas Tank Company Stretch Tanks: Manufacturer part # 07010002 - Handcrafted tank is quality constructed using 16-gauge cold-rolled steel. Each tank has been TIG welded, then pressure tested to the highest standards. Has four mounts on the tank bottom and a tunnel width of 2 1/4 in.. 22mm petcock fitting. 1/8" NPT threaded crossover fittings. Require custom mounting; will not work on frames with standard Fat Bob tank mounts. Made in the U.S.A., , TANK STYLE - Streamline. Pointed at the rear with sqaure end. Notched for seat tube clearance. Capacity is approximately 4.5 gal.. 27" L X 11" W. Screw-in cap Bung. Work well with arched backbone frames, , NOTE: Not for use on fuel-injected models, , NOTE: The use of a custom seat is required, , NOTE: Tanks with screw-in caps use 82-E96 style caps (sold separately), , NOTE: This item ships 3-4 days after order is placed, , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. 07010002
1 on Hand
More Info/Options for H18825 Independent Gas Tank Company Stretch Tanks
|
|
|
|
$789.99
H18828 Independent Gas Tank Company Stretch Tanks
Dennis Kirk Part #: H18828
H18828 Independent Gas Tank Company Stretch Tanks: Manufacturer part # 07010004 - Handcrafted tank is quality constructed using 16-gauge cold-rolled steel. Each tank has been TIG welded, then pressure tested to the highest standards. Has four mounts on the tank bottom and a tunnel width of 2 1/4 in.. 22mm petcock fitting. 1/8" NPT threaded crossover fittings. Require custom mounting; will not work on frames with standard Fat Bob tank mounts. Made in the U.S.A., , TANK STYLE - Chopper. Square end and rounded sides. Capacity is approximately 4.5 gal.. 27" L X 11" W. Screw-in cap bung, , NOTE: Not for use on fuel-injected models, , NOTE: The use of a custom seat is required, , NOTE: Tanks with screw-in caps use 82-E96 style caps (sold separately), , NOTE: This item ships 3-4 days after order is placed, , WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.. 07010004
1 on Hand
More Info/Options for H18828 Independent Gas Tank Company Stretch Tanks
|
|
|
|
$788.99
Pro-One Smooth Chrome Billet Outer Primary Cover 148994
Dennis Kirk Part #: 148994
Pro-One Smooth Chrome Billet Outer Primary Cover 148994: Manufacturer part # 200460 - Machined from solid billet aluminum, each cover is fully polished to a mirror finish and then chromed plated. Matching derby cover and inspection covers are available separately. , , Included items 1. (1) Billet outer primary cover. 2. (1) Large Diameter (gray) bushing. 3. (1) Brass starter pinion bushing. 4. (1) 3/8-16 Thin pattern nylock. 5. (1) 3/8-16 X 3/4" Carriage bolt. This item ships in 3-4 business day after the order is placed.. 200460
1 on Hand
More Info/Options for Pro-One Smooth Chrome Billet Outer Primary Cover 148994
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
$787.99
Yoshimura R-22 Bling Stainless Bolt-On Muffler 4402335
Dennis Kirk Part #: 4402335
Yoshimura R-22 Bling Stainless Bolt-On Muffler 4402335: Manufacturer part # 1117235 - Yoshimura designed this muffler first for power, then added incredible style. Highly polished stainless steel Tri-Oval muffler adds ground clearance and lets your engine breathe. Functional air vents on the polished stainless steel Tri-Oval end cap help dissipate hot muffler gasses to provide increased performance. . Installation of a new exhaust system may change your motorcycles fuel-air mixture requirements. Please consult the manufacturer directly with questions regarding any modifications that may need to be made during, or after installing their product. If a jet kit or EFI controller is recommended please see the Intake/Fuel section for products available. Exhaust discoloration (blueing) is caused by engine conditions such as cam timing, fuel-air mixture, operating temperature, etc. It is not the result of defective manufacturing; therefore it is not covered by any warranty. See the Chems/Lubes section for products to help remove or prevent exhaust discoloration.. 1117235
| |
