|
|
$304.99
H51607 Andrews N6 Grind Cam for XL 00-03 and Buell 00-02
Dennis Kirk Part #: H51607
H51607 Andrews N6 Grind Cam for XL 00-03 and Buell 00-02: Manufacturer part # 298170 - Andrews Products was founded in the spring of 1972 and for 30+ years has specialized in making camshafts and transmission gears for the performance motorcycle market. Performance cams designed by Andrews for XL 883, and 1200 Evolution 00-03 and Buell 00-02 models. Cams run up to 6000 rpm with stock hydraulic lifters; for this reason, it is recommended that solids NOT be installed. Stock base circle sizes so stock pushrods can be used. N6 Grind Cam , Intake: Open: 34 degrees. Close: 50 degrees. Duration at .053: 264 degrees. Valve Lift: .500. , Exhaust: Open: 56 degrees. Close: 28 degrees. Duration at .053: 264 degrees. Valve Lift: .500.. 298170
1 on Hand
More Info/Options for H51607 Andrews N6 Grind Cam for XL 00-03 and Buell 00-02
|
|
|
|
|
|
$171.99
H51387 Andrews A Grind Cam
Dennis Kirk Part #: H51387
H51387 Andrews A Grind Cam: Manufacturer part # 212280 - Youll get more mid-range and top-end power for your street or drag bike. These cams work with solid or hydraulic lifters, and the idle remains unaffected up to 6,000 rpm with stock valve springs.. , , A GRIND CAMS , , Bolt right into 70-E77 Big Twin engines with no head work. Spring travel and clearance must be checked. , , INTAKE: Opens: 21 degrees. Closes: 43 degrees. Duration @ .053: 244 degrees. Valve Lift Shovel: .450. Pan: .470. , EXHAUST: Opens: 43 degrees. Closes: 21 degrees. Duration @ .053: 244 degrees. Valve Lift Shovel: .450. Pan: .470. NOTE: On late 77 and later engines, the pitch diameter on the camshaft, pinion gear and breather valve gear was changed. These components are not interchangeable with earlier-style components unless replaced in sets only. Late 77 and later gear sets are identified by a circular groove machined in the outer face of the cam gear.. 212280
2 on Hand
More Info/Options for H51387 Andrews A Grind Cam
|
|
|
|
|
|
$299.99
Andrews Gear Driven 37HG Grind Cam 140110
Dennis Kirk Part #: 140110
Andrews Gear Driven 37HG Grind Cam 140110: Manufacturer part # 216337G - Series HG gear drive cams, they are specifically designed to run with new S&S gear drives.. The cams listed below are the same designs as gear drive cams that have been made for 99-06 engines. Gear drives made for 99-05 engines will not fit 07 Twin cam engines or 06 Dyna engines. HG series cam kit also include two plates for closing lubricating oil feed holes which are intended for stock chains, not 07 style gear drives. Performance with any of the H cams listed will be similar to the same grids with earlier 99-05 engines. NOTE: Will require the purchase of a gear set (sold separately) for installation 37HG GRIND CAMS INFORMATION: Bolt-in cams have shown 80+ rear wheel hp. Smooth idle with broad torque band. Run best with low restriction exhaust (2200-5800 rpm). Can be used with stock valve springs and tappets. Works well with carbs and fuel injection. INTAKE: Opens: 14 degrees. Closes: 42 degrees. Duration @ .053: 236 degrees. Duration @ .020: 272 degrees. Valve Lift: .510. Lift TDC: .151. EXHAUST: Opens: 48 degrees. Closes: 12 degrees. Duration @ .053: 240 degrees. Duration @ .020: 276 degrees. Valve Lift: .510. Lift TDC: .140.. 216337G
1 on Hand
More Info/Options for Andrews Gear Driven 37HG Grind Cam 140110
|
|
|
|
|
|
$171.99
H51342 Andrews No 1 Grind Cams for FX and FL L77-84
Dennis Kirk Part #: H51342
H51342 Andrews No 1 Grind Cams for FX and FL L77-84: Manufacturer part # 212150 - Shorter durations and higher lifts mean broad torque output throughout rev range. Grind No. 1 is similar to an "A" grind cam for 74" and 80" models, but in a low compression version. Grind No. 2 gives better power throughout rev range; the low compression version of a "B" grind cam- H51-343. Designed for hydraulics, can also be run with solids. Not for Evolution. A GRIND CAM: , Intake: Open: 21 degrees. Close: 43 degrees. Duration at .053: 244 degrees. Valve Lift: Shovel .450. Pan .470. , Exhaust: Open: 43 degrees. Close: 21 degrees. Duration at .053: 244 degrees. Valve Lift: Shovel .450. Pan .470. , B GRIND CAM: , Intake: Open: 26 degrees. Close: 50 degrees. Duration at .053: 256 degrees. Valve Lift: Shovel .450. Pan .470. , Exhaust: Open: 50 degrees. Close: 26 degrees. Duration at .053: 256 degrees. Valve Lift: Shovel .485. Pan .507.. 212150
1 on Hand
More Info/Options for H51342 Andrews No 1 Grind Cams for FX and FL L77-84
|
|
|
|
$354.99
Andrews Gear Driven 59HG Grind Cam 140114
Dennis Kirk Part #: 140114
Andrews Gear Driven 59HG Grind Cam 140114: Manufacturer part # 216359G - Series HG gear drive cams, they are specifically designed to run with new S&S gear drives.. The cams listed below are the same designs as gear drive cams that have been made for 99-06 engines. Gear drives made for 99-05 engines will not fit 07 Twin cam engines or 06 Dyna engines. HG series cam kit also include two plates for closing lubricating oil feed holes which are intended for stock chains, not 07 style gear drives. Performance with any of the H cams listed will be similar to the same grids with earlier 99-05 engines. NOTE: Will require the purchase of a gear set (sold separately) for installation 59HG GRIND CAMS INFORMATION: For 95 in.+ motors with 10:1 compression ratio or higher. Maximum torque and HP at middle and upper rpm ranges (2400-6200 rpm). Coil bind must be checked, but can use stock tappets. INTAKE: Opens: 29 degrees. Closes: 57 degrees. Duration @ .053: 266 degrees. Duration @ .020: 303 degrees. Valve Lift: .590. Lift TDC: .238. EXHAUST: Opens: 63 degrees. Closes: 27 degrees. Duration @ .053: 270 degrees. Duration @ .020: 307 degrees. Valve Lift: .590. Lift TDC: .218.. 216359G
1 on Hand
More Info/Options for Andrews Gear Driven 59HG Grind Cam 140114
|
|
|
|
|
|
$171.99
H51453 Andrews A Grind Cam
Dennis Kirk Part #: H51453
H51453 Andrews A Grind Cam: Manufacturer part # 212270 - Youll get more mid-range and top-end power for your street or drag bike. These cams work with solid or hydraulic lifters, and the idle remains unaffected up to 6,000 rpm with stock valve springs.. , , A GRIND CAMS , , Bolt right into 48-69 Big Twin engines with no head work. Spring travel and clearance must be checked. , , INTAKE: Opens: 21 degrees. Closes: 43 degrees. Duration @ .053: 244 degrees. Valve Lift Shovel: .450. Pan: .470. , EXHAUST: Opens: 43 degrees. Closes: 21 degrees. Duration @ .053: 244 degrees. Valve Lift Shovel: .450. Pan: .470.. 212270
2 on Hand
More Info/Options for H51453 Andrews A Grind Cam
|
|
|
|
|
|
$299.99
Andrews Gear Driven 67HG Grind Cam 140117
Dennis Kirk Part #: 140117
Andrews Gear Driven 67HG Grind Cam 140117: Manufacturer part # 216367G - Series HG gear drive cams, they are specifically designed to run with new S&S gear drives.. The cams listed below are the same designs as gear drive cams that have been made for 99-06 engines. Gear drives made for 99-05 engines will not fit 07 Twin cam engines or 06 Dyna engines. HG series cam kit also include two plates for closing lubricating oil feed holes which are intended for stock chains, not 07 style gear drives. Performance with any of the H cams listed will be similar to the same grids with earlier 99-05 engines. NOTE: Will require the purchase of a gear set (sold separately) for installation 67HG GRIND CAMS INFORMATION: Hi-lift performance cams for 95-107+ inches, 10.0 to 10.8-compression ratio with high-flow head setup; (2600-6400+ rpm).. INTAKE: Opens: 24 degrees. Closes: 48 degrees. Duration @ .053: 252 degrees. Duration @ .020: 287 degrees. Valve Lift: .570. Lift TDC: .209. EXHAUST: Opens: 48 degrees. Closes: 22 degrees. Duration @ .053: 260 degrees. Duration @ .020: 297 degrees. Valve Lift: .570. Lift TDC: .187.. 216367G
1 on Hand
More Info/Options for Andrews Gear Driven 67HG Grind Cam 140117
|
|
|
|
$265.99
Andrews 41N Grind Cam Rollers 140043
Dennis Kirk Part #: 140043
Andrews 41N Grind Cam Rollers 140043: Manufacturer part # 216826 - Allows you to upgrade your 99-06 Twin Cam (except 06 Dyna Glide) to the newer roller-style cam chains and replaces the spring tension cam chain adjusters with the later-style hydraulic adjusters for longer life. Cam grinds listed are designed to be used with stock lifters. They require the installation of a 2007 cam plate, oil pump, cam sprockets and chains, and both hydraulic chain adjusters. These parts are not included and must be purchased separately. A list of required components is supplied with each set of cams Performance should be similar to earlier bikes with the same cam grinds.. , NOTE: 99-06 Twin Cam motors (except 06 Dyna Glide) cannot use the 2007 cams, as the bearing journal on the earlier motors is .875 in. in diameter and the 2007 cams are 1.000 in. in diameter. The "N" series of cams feature the .875 in. bearing journal, yet still accept the new style cam support plate., NOTE: 99-01 model motors must use the Andrews rear cam sprocket Drag PART #140050. 2002-2006 models must use the stock rear cam sprocket, OEM # 25728-06., NOTE: Installer must check coil bind, valve-to-valve clearance and valve-to-piston clearance., , FOR 99-06 TWIN CAM (EXCEPT 06 DYNA GLIDE). 216826
1 on Hand
More Info/Options for Andrews 41N Grind Cam Rollers 140043
|
|
|
|
|
|
$171.99
H51452 Andrews J Grind Cam for Big Twin 70-E77
Dennis Kirk Part #: H51452
H51452 Andrews J Grind Cam for Big Twin 70-E77: Manufacturer part # 212020 - Youll get more mid-range and top-end power for your street or drag bike. These cams work with solid or hydraulic lifters, and the idle remains unaffected up to 6,000 rpm with stock valve springs. , , J GRIND CAMS , , For mild street applications. Adds more power throughout rpm range and maintains a smooth idle. Bolts in with no head work. , , INTAKE: Opens: 21 degrees. Closes: 41 degrees. Duration @ .053: 242 degrees. Valve Lift Shovel: .405. Pan: .425. , EXHAUST: Opens: 41 degrees. Closes: 21 degrees. Duration @ .053: 242 degrees. Valve Lift Shovel: .405. Pan: .425. NOTE: On late 77 and later engines, the pitch diameter on the camshaft, pinion gear and breather valve gear was changed. These components are not interchangeable with earlier-style components unless replaced in sets only. Late 77 and later gear sets are identified by a circular groove machined in the outer face of the cam gear.. 212020
2 on Hand
More Info/Options for H51452 Andrews J Grind Cam for Big Twin 70-E77
|
|
|
|
$299.99
Andrews Gear Driven 32HG Grind Cam 140109
Dennis Kirk Part #: 140109
Andrews Gear Driven 32HG Grind Cam 140109: Manufacturer part # 216332G - Series HG gear drive cams, they are specifically designed to run with new S&S gear drives.. The cams listed below are the same designs as gear drive cams that have been made for 99-06 engines. Gear drives made for 99-05 engines will not fit 07 Twin cam engines or 06 Dyna engines. HG series cam kit also include two plates for closing lubricating oil feed holes which are intended for stock chains, not 07 style gear drives. Performance with any of the H cams listed will be similar to the same grids with earlier 99-05 engines. NOTE: Will require the purchase of a gear set (sold separately) for installation 32HG GRIND CAMS INFORMATION: Hi-lift High lift version of 31G. Much more (-20%) power thru rpm range with 10:1+ compression ratio. 2800-5800 rpm range. INTAKE: Opens: 10 degrees. Closes: 46 degrees. Duration @ .053: 236 degrees. Duration @ .020: 272 degrees. Valve Lift: .570. Lift TDC: .131. EXHAUST: Opens: 52 degrees. Closes: 08 degrees. Duration @ .053: 240 degrees. Duration @ .020: 276 degrees. Valve Lift: .570. Lift TDC: .120.. 216332G
1 on Hand
More Info/Options for Andrews Gear Driven 32HG Grind Cam 140109
|
|
|
|
$171.99
H51456 Andrews J Grind Cam
Dennis Kirk Part #: H51456
H51456 Andrews J Grind Cam: Manufacturer part # 212011 - You will get more mid-range and top-end power for your street or drag bike. These cams work with solid or hydraulic lifters, and the idle remains unaffected up to 6,000 rpm with stock valve springs. , , J GRIND CAMS , , For mild street applications. Adds more power throughout rpm range and maintains a smooth idle. Bolts in with no head work. , , INTAKE: Opens: 21 degrees. Closes: 41 degrees. Duration @ .053: 242 degrees. Valve Lift Shovel: .405. Pan: .425. , EXHAUST: Opens: 41 degrees. Closes: 21 degrees. Duration @ .053: 242 degrees. Valve Lift Shovel: .405. Pan: .425.. 212011
1 on Hand
More Info/Options for H51456 Andrews J Grind Cam
|
|
|
|
$304.99
H51606 Andrews N4 Grind Cam for XL 00-03 and Buell 00-02
Dennis Kirk Part #: H51606
H51606 Andrews N4 Grind Cam for XL 00-03 and Buell 00-02: Manufacturer part # 298150 - Andrews Products was founded in the spring of 1972 and for 30+ years has specialized in making camshafts and transmission gears for the performance motorcycle market. Performance cams designed by Andrews for XL 883, and 1200 Evolution 00-03 and Buell 00-02 models. Cams run up to 6000 rpm with stock hydraulic lifters; for this reason, it is recommended that solids NOT be installed. N4 is for stock or modified applications, have a slightly higher idle speed, can be used w/ stock hydraulic lifters and springs, and have 2500 - 6000 rpm range. Stock base circle sizes so stock pushrods can be used. N4 Grind Cam , Intake: Open: 30 degrees. Close: 46 degrees. Duration at .053: 256 degrees. Valve Lift: .490. , Exhaust: Open: 52 degrees. Close: 24 degrees. Duration at .053: 256 degrees. Valve Lift: .490.. 298150
1 on Hand
More Info/Options for H51606 Andrews N4 Grind Cam for XL 00-03 and Buell 00-02
|
|
|
|
$171.99
H51463 Andrews AB Grind Cam for Big Twin 70-E77
Dennis Kirk Part #: H51463
H51463 Andrews AB Grind Cam for Big Twin 70-E77: Manufacturer part # 212320 - Youll get more mid-range and top-end power for your street or drag bike. These cams work with solid or hydraulic lifters, and the idle remains unaffected up to 6,000 rpm with stock valve springs.. , , AB GRIND CAMS , , Bolt-in street cams have an A intake plus a long duration exhaust for cooler running and high-end power. Suitable for hydraulic lifters. , , INTAKE: Opens: 21 degrees. Closes: 50 degrees. Duration @ .053: 244 degrees. Valve Lift Shovel: .450. Pan: .470. , EXHAUST: Opens: 43 degrees. Closes: 26 degrees. Duration @ .053: 256 degrees. Valve Lift Shovel: .450. Pan: .470. NOTE: On late 77 and later engines, the pitch diameter on the camshaft, pinion gear and breather valve gear was changed. These components are not interchangeable with earlier-style components unless replaced in sets only. Late 77 and later gear sets are identified by a circular groove machined in the outer face of the cam gear.. 212320
1 on Hand
More Info/Options for H51463 Andrews AB Grind Cam for Big Twin 70-E77
|
|
|
|
|
|
$171.99
H51388 Andrews AB Grind Cam for Big Twin L77-84 (except 80-81)
Dennis Kirk Part #: H51388
H51388 Andrews AB Grind Cam for Big Twin L77-84 (except 80-81): Manufacturer part # 212335 - Youll get more mid-range and top-end power for your street or drag bike. These cams work with solid or hydraulic lifters, and the idle remains unaffected up to 6,000 rpm with stock valve springs.. , , AB GRIND CAMS , , Bolt-in street cams have an A intake plus a long duration exhaust for cooler running and high-end power. Suitable for hydraulic lifters. , , INTAKE: Opens: 21 degrees. Closes: 50 degrees. Duration @ .053: 244 degrees. Valve Lift Shovel: .450. Pan: .470. , EXHAUST: Opens: 43 degrees. Closes: 26 degrees. Duration @ .053: 256 degrees. Valve Lift Shovel: .450. Pan: .470. NOTE: On late 77 and later engines, the pitch diameter on the camshaft, pinion gear and breather valve gear was changed. These components are not interchangeable with earlier-style components unless replaced in sets only. Late 77 and later gear sets are identified by a circular groove machined in the outer face of the cam gear.. 212335
1 on Hand
More Info/Options for H51388 Andrews AB Grind Cam for Big Twin L77-84 (except 80-81)
|
|
|
|
$265.99
Andrews TW31S Chain Driven Cam 149902
Dennis Kirk Part #: 149902
Andrews TW31S Chain Driven Cam 149902: Manufacturer part # 216331 - Andrews Products is recognized world wide and throughout the Motor Sports community as an industry leader. Andrews Products grind its cams using computer-aided cam design capabilities. This superior technology gives the utmost in both performance and reliability. Only the best alloy steel billets and heat treating processes are used. The power in a Harley Twin Cam engine is completely released only when superior Andrews computer-designed high- performance cams are installed. Cams come with new bearings (1 roller and 1 ball) and thrust washers. Andrews recommends using their steel cam drive sprocket H11-120 and crankshaft cam drive sprocket H14-175 (must be purchased separately).. , , TW31S Grind Cams. Bolt-in cam for motors with 95 inches and 9.8 to 10.2 compression ratio. Lower TDC lift for easy installation. Similar to TW37 with different timing (2000-5600 rpm power range. Can be used with stock valve springs and tappets . , , NOTE: 00-06 model cams use a splined cam drive sprocket. These cams will fit in the 1999 Twin Cam motor, but the splined cam drive sprocket OEM #25716-99 or H11-120 must be used.. , , NOTE: Installer must check coil bind, valve clearance and valve-to-piston clearance.. , , INTAKE: Opens: 10 degrees. Closes: 46 degrees. Duration @ .053: 236 degrees. Duration @ .020: 272 degrees. Valve Lift: .510. Lift TDC: .131. , EXHAUST: Opens: 52 degrees. Closes: 08 degrees. Duration @ .053: 240 degress. Duration @ .020: 276 degrees. Valve Lift: .510. Lift TDC: .120.. 216331
1 on Hand
More Info/Options for Andrews TW31S Chain Driven Cam 149902
|
|
|
|
