|
|
|
|
$136.99
Harley-Davidson > Forward Controls & Pegs > Footpegs & Hardware: Kuryakyn Highway Pegs 7887
Manufacturer: Kuryakyn
Dennis Kirk Part #: 493527
Kuryakyn Highway Pegs: Manufacturer part # 7887 - Chrome plated arms are adjustable so you can fine-tune the footpeg location. Compatible with stock forward controls. Recommended for use by riders with inseam of 34 inches or longer. For models listed using H-D forward controls NOs. 49080-03 or 49080-06. , , Works with the following pegs: Stiletto - part no. 493208 Switchblade - part no. 505478 Dually - part no. 492649 Large ISO - part no. 492648 Small ISO - part no. 492647 Retro - part no. 492651 Pilot - part no. 490660 ISO Wing - part no. 492650. , , Installation moves the stock brake side control assembly outward 3/8in. If using aftermarket exhaust be sure to verify there is adequate clearance between the brake pivot and front exhaust header pipe.. 7887
4 on hand
More Info/Options for Kuryakyn Highway Pegs 7887
|
|
|
|
$139.99
Harley-Davidson > Forward Controls & Pegs > Footpegs & Hardware: Kuryakyn Dually ISO Pegs with Offset Mounts & 1.35 in. Clamps 7920
Manufacturer: Kuryakyn
Dennis Kirk Part #: 505495
Kuryakyn Dually ISO Pegs with Offset Mounts & 1.35 in. Clamps: Manufacturer part # 7920 - These highway pegs utilize our unique offset mount to allow riders a range of adjustment not possible with other clamp-on style highway pegs. The offset can be rotated 360 degrees in a 4 diameter circle to accommodate tall, short, or average height riders. These can be installed on any round tubing (frames or engine guards), but it is important to keep in mind that the footpeg itself will end up perpendicular to the bar to which it is mounted. If your engine guard is angled in such a way so that the peg will not be level once installed, look at our right angle mounts. Picture: At the bottom Helpful Hint: If you are unsure of the diameter of the tubing on which you would like to install the highway pegs and do not have a dial at your disposal, here is an easy way to figure it out. You will need a piece of heavy paper or cardboard, a ruler, a pencil, and a scissors. Use the pencil and ruler to make to marks on the edge of the paper 1 in. apart. Take the scissors and cut lines perpendicular to the edge of the paper at the marks you just made. Fold the resulting flap of paper out of the way. Next, take the piece of paper to the bike and check to see if the tubing will slip into the opening you've made in the edge of the paper. If the opening is too small, repeat the procedure enlarging the opening to 1-1/8, 1-1/4, 1.35, 1-1/2 until you find one that will fit.. 7920
7 on hand
More Info/Options for Kuryakyn Dually ISO Pegs with Offset Mounts & 1.35 in. Clamps 7920
|
|
|
|
|
|
$153.99
Harley-Davidson > Forward Controls & Pegs > Footpegs & Hardware: Kuryakyn Adjustable Footpegs for Dressers 7926
Manufacturer: Kuryakyn
Dennis Kirk Part #: H50262
Kuryakyn Adjustable Footpegs for Dressers: Manufacturer part # 7926 - Fits models listed with stock passenger boards. Our original retractable passenger pegs redefined passenger comfort.. The test of time and input from customers has helped us to refine this popular accessory, improving its fit and function.. This kit gives you the ability to move your feet up or down and best of all when the driver has his or her feet on the highway pegs you can stretch your legs by laying your calves on the footrests.. Your passenger will love the flexibility.. A new BOLT ACTION locking device on the swing arm to lock in place, adds two intermediate positions to make hours in the passenger seat more enjoyable for passengers of different heights.. A revised mounting system allows easier installation and improved fit on newer models.. Does not interfere with footboard operation.. , , NOTES:, , Motorcycles that are equipped with Rinehart true dual exhaust will require Part No. 49-2593 left side extended passenger board mount. 7926
6 on hand
More Info/Options for Kuryakyn Adjustable Footpegs for Dressers 7926
|
|
|
|
|
|
$22.99
Harley-Davidson > Forward Controls & Pegs > Footpegs & Hardware: Kuryakyn Magnum Quick Clamp 1 1/8 in. I.D. 7941
Manufacturer: Kuryakyn
Dennis Kirk Part #: H500526
Kuryakyn Magnum Quick Clamp 1 1/8 in. I.D.: Manufacturer part # 7941 - Stainless steel construction for fast, simple installation. No more stripped bolt heads. Fits H-D frame down-tubes. Sold each. Choose the correct size clamp for your application. In order to do this you will need to determine what size engine guard you have on your motorcycle. If you do not have a dial caliper available, you can easily determine the diameter of the engine guard. You will need a piece of heavy paper or cardboard, a ruler, a pencil, and a scissors. Use the pencil and ruler to make to marks on the edge of the paper 1 in. apart. Take the scissors and cut lines perpendicular to the edge of the paper at the marks you just made. Fold the resulting flap of paper out of the way. Next, take the piece of paper to the bike and check to see if the tubing will slip into the opening youve made in the edge of the paper. If the opening is too small, repeat the procedure enlarging the opening to 1-1/8, 1-1/4, 1.35, and 1-1/2 until you find one that will fit. We have made a lot of friends with these!. Stainless steel construction for superior strength and hinged design for fast simple installation. No more stripped bolt heads!. By the way. . . Cobra engine guards are 1-1/4 diameter. Frame down tubes on VN1500 and some other Japanese cruisers are 1.35 diameter. The curved part of a Valkyrie engine guard in front of the valve covers will accept a 1-1/8 diameter clamp. Frame down tubes on a V-Star 650 are 1-1/4 in diameter.. 7941
Expected Soon
More Info/Options for Kuryakyn Magnum Quick Clamp 1 1/8 in. I.D. 7941
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
$107.99
Harley-Davidson > Forward Controls & Pegs > Footpegs & Hardware: Kuryakyn Dually ISO Highway Peg with 1 1/4 in. Quick Clamp 7992
Manufacturer: Kuryakyn
Dennis Kirk Part #: H500480
Kuryakyn Dually ISO Highway Peg with 1 1/4 in. Quick Clamp: Manufacturer part # 7992 - The most comfortable, stylish pegs on the road. Twice the surface area and nearly twice as many vibration-absorbing ISO pads. Thin profile and sleek appearance complement any custom or stock machine. Rubber pads are easily replaceable, and the chrome will last for years. Using our patented Magnum Quick Clamp, they are a snap to install and provide long-haul comfort. These can be installed on any round tubing (frames or engine guards), but it is important to keep in mind that the footpeg itself will end up perpendicular to the bar to which it is mounted. If your engine guard is angled in such a way so that the peg will not be level once installed, check out our adapters w/adjustable stop P/N 50-5503. Measurement: 5 in. L x 2 1/2 in. W. Helpful Hint: If you are unsure of the diameter of the tubing on which you would like to install the highway pegs and do not have a dial at your disposal, here is an easy way to figure it out. You will need a piece of heavy paper or cardboard, a ruler, a pencil, and a scissors. Use the pencil and ruler to make to marks on the edge of the paper 1 in. apart. Take the scissors and cut lines perpendicular to the edge of the paper at the marks you just made. Fold the resulting flap of paper out of the way. Next, take the piece of paper to the bike and check to see if the tubing will slip into the opening you've made in the edge of the paper. If the opening is too small, repeat the procedure enlarging the opening to 1-1/8, 1-1/4, 1.35, 1-1/2 until you find one that will fit.. 7992
10 on hand
More Info/Options for Kuryakyn Dually ISO Highway Peg with 1 1/4 in. Quick Clamp 7992
|
|
|
|
|
|
|
|
Moose Extended Lift Push Tube
Vance & Hines Dresser Dual Header Pipes 16729
Motion Pro SyncPro Carburetor Tuner
Kuryakyn Wheel Chock 922
Vance & Hines Big Radius Exhaust 26029
Caliber Poly-Shield III Salt Shield 13401
Parts Unlimited Large Universal Cover CS-1002
Kuryakyn Condor Pit-Stop/Trailer Stop Wheel Chock 920
Parts Unlimited Total Cover TC-1005
Vance & Hines Straight Shot HS Slip-Ons 16819
Vance & Hines Big Shot Duals 17925
Caliber LowPro Low Profile Wide 8 in. Trailer Guide and Protection System 13322
HJC Electric Shield
Battery Tender Battery Tender Jr. 12-Volt Model
BUB Rinehart 3 1/2 in. Slip-On Mufflers
Kuryakyn GranTour Bag 4141
Vance & Hines Big Radius Exhaust 26003
NGK Resistor Spark Plug BR9ES
JPS Blue Polyurethane Fuel Line
HJC Universal Quick Release Buckle
RBI Inc Bearing OEM Standard No 62052RS