|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
$noprice
S&S Manifold for 54mm S&S Single Bore Throttle Bodies 173046
Dennis Kirk Part #: 173046
S&S Manifold for 54mm S&S Single Bore Throttle Bodies 173046: Designed for riders seeking the greatest possible performance gains from their fuel-injected engines. By utilizing air column inertia and carefully timed gas dynamic pressure waves, the S&S VFI Tuned Induction systems ram additional air into the cylinders for increased mid-range torque. Forward swept design of the intake runners further improves power by providing the engine with cooler, denser air. For maximum tunability and performance gains an S&S Variable Fuel Injection (VFI) module is recommended (sold separately), but any compatible, programmable module with enough capability and tuning range can be used. Components must be purchased separately to complete a Single-Bore EFI assembly. NOTE: For 80 in., 88 in., 89 in., 95 in., 96 in., 103 in., and 106 in. motors.
1 on Hand
More Info/Options for S&S Manifold for 54mm S&S Single Bore Throttle Bodies 173046
|
|
|
|
|
|
$noprice
H170406 S&S .032 Intermediate Jet Kit for S&S carbs
Dennis Kirk Part #: H170406
H170406 S&S .032 Intermediate Jet Kit for S&S carbs: Manufacturer part # 117112 - For jetting most stock and moderate performance engines up to about 93". Each jet pack includes one each intermediate jets .025, .0265, .028, .0295 and one each main jets .062, .064, .066, .068, .070, .072, .074. Replacement jets also available separately. , , HIGH RANGE JET KITS, For jetting some stock and all moderate performance engines. Each jet pack includes one each intermediate jets .0295, .031, .032, .033 and one each main jets .072, .074, .076, .078, .080, .082, .084. Replacement jets also available separately.. 117112
3 on Hand
More Info/Options for H170406 S&S .032 Intermediate Jet Kit for S&S carbs
|
|
|
|
$noprice
S&S Super G Carb Kit for 116 in. Super Sidewinder Hot Set-Up Kit 165016
Dennis Kirk Part #: 165016
S&S Super G Carb Kit for 116 in. Super Sidewinder Hot Set-Up Kit 165016: Manufacturer part # 110466 - Include 4 in. bore cylinders, pistons, S&S Super Stock cylinder heads, S&S gear drive cam kit, chromoly steel pushrod kit, gaskets and installation instructions. Comes with S&S 585G cams and 10.1:1 pistons. Engine cases must be bored to accept the 4 in. cylinders. Super G carb kits (sold separately) include the classic S&S teardrop air cleaner and the correct length manifold for the intended kit. Made in the U.S.A.. , , NOTE: This project requires a skilled technician. It is the responsibility of the person assembling the parts to check all clearances and assembly specifications., , NOTE: This item ships in 3-4 days after the order is placed .. 110466
1 on Hand
More Info/Options for S&S Super G Carb Kit for 116 in. Super Sidewinder Hot Set-Up Kit 165016
|
|
|
|
|
|
|
|
$noprice
S&S High Flow Air Filter and Adaptor Kit 304495
Dennis Kirk Part #: 304495
S&S High Flow Air Filter and Adaptor Kit 304495: Manufacturer part # 170045 - High-flow filter designed especially for Super E and G carburetors. Filter is 1" taller than standard filter and features a low-restriction, pre-oiled filter element. Allows for a 37% increase in airflow. Filter and adapters extend the teardrop housing out 1" for better exposure and a high-performance street racer look. Kit installs in minutes; no permanent modifications required. , , NOTE: Not for use with S&S Super B or Super D carburetors, or Super E and G Kits for Buells.. 170045
9 on Hand
More Info/Options for S&S High Flow Air Filter and Adaptor Kit 304495
|
|
|
|
|
|
$noprice
S&S Flange-Mount Intake Manifold 172896
Dennis Kirk Part #: 172896
S&S Flange-Mount Intake Manifold 172896: Manufacturer part # 161628 - Fits the models listed with S&S E, L, Super A, B, E H-D Tillotson, Bendix and Keihin carbs. Can be used to replace stock compliance fitting manifold on 84-89 and stock rigid-mount manifold from 90-99. Use with stock or S&S cylinder heads. For use with stock 5.5550in. length cylinders. Requires the use of S&S intake seals (part number 17-2782) and flanges (part numbers: 18-3046 (front) and 18-3047 (rear).. 161628
2 on Hand
More Info/Options for S&S Flange-Mount Intake Manifold 172896
|
|
|
|
$noprice
H170402 S&S .028 Intermediate Jet Kit for S&S carbs
Dennis Kirk Part #: H170402
H170402 S&S .028 Intermediate Jet Kit for S&S carbs: Manufacturer part # 117109 - For jetting most stock and moderate performance engines up to about 93". Each jet pack includes one each intermediate jets .025, .0265, .028, .0295 and one each main jets .062, .064, .066, .068, .070, .072, .074. Replacement jets also available separately. , , HIGH RANGE JET KITS For jetting some stock and all moderate performance engines. Each jet pack includes one each intermediate jets .0295, .031, .032, .033 and one each main jets .072, .074, .076, .078, .080, .082, .084. Replacement jets also available separately.. 117109
4 on Hand
More Info/Options for H170402 S&S .028 Intermediate Jet Kit for S&S carbs
|
|
|
|
|
|
|
|
|
|
$noprice
H19302 S&S 42 in. Dual Cable Throttle Assembly Kit
Dennis Kirk Part #: H19302
H19302 S&S 42 in. Dual Cable Throttle Assembly Kit: Manufacturer part # 190482 - These throttle assembly kits are designed to work with the S&S Super E & G carbs or any other butterfly-type carburetor with 81 and later OEM-style throttle linkage. Contents of each kit includes a two-cable throttle assembly with matching grips, two OEM style throttle cables and hardware. Measured from throttle grip to end of cable housing; barrel fittings are soldered in place (not for CV carbs). Replacement cables: H19304 Throttle, H19306 Idle.. 190482
1 on Hand
More Info/Options for H19302 S&S 42 in. Dual Cable Throttle Assembly Kit
|
|
|
|
|
|
|
|
|
|
$noprice
H19303 S&S 48 in. Dual Cable Throttle Assembly Kit
Dennis Kirk Part #: H19303
H19303 S&S 48 in. Dual Cable Throttle Assembly Kit: Manufacturer part # 190449 - These throttle assembly kits are designed to work with the S&S Super E & G carbs or any other butterfly-type carburetor with 81 and later OEM-style throttle linkage. Contents of each kit includes a two-cable throttle assembly with matching grips, two OEM style throttle cables and hardware. Measured from throttle grip to end of cable housing; barrel fittings are soldered in place (not for CV carbs). Replacement cables: H19307 Throttle, H19308 Idle.. 190449 | |
